Get the cranked, tube-driven tone that only a vintage amp can provide with Choptones Fend B45 from Overloud, an add on for TH-U rig player that recreates the sound of a Fender Bassbreaker 45 all-tube head. Loaded with 7 cabs, 11 mics, 14 boost pedals, and 86 rigs total, this library is ideal for a wide range of styles.

Just like the original Bassbreaker, Fend B45 has bright and clean channels, which can be connected in series for extra dirt. Within TH-U, you can freely place your 11 different mics in a 3D space for your ideal mic setup. Note, this rig library is for use with TH-U rig player only. TH-U supports macOS and Windows computers and AAX, VST, and AU plug-in formats.

Fender Bassbreaker 45 All-Tube Head    For Cranked Vintage Tones    86 Rigs, 7 Cabs, 11 Mics, and 14 Boosts    For TH-U Rig Player Only    Freely Place Mics in 3D Space    2 Serial Channels: Bright and Clean    For macOS and Windows Computers

• Fender Bluesbreaker 2x12 loaded with Celestion V-Type and Neo V-Type
• Marshall 1960 4x12 with Celestion V30
• Hughes & Kettner 4x12 with Celestion G12M
• Mesa/Boogie 2x12 loaded with Celestion V-Type
• Bogner 1x12 with Celestion G12M
• Morgan 1x12 with Celestion Creamback G12H75
• Suhr 1x12 loaded with Celestion G12M

• Shure SM57 and SM58
• Shure Unidyne III
• Shure SM7
• Sennheiser e609 and e906
• Sennheiser MD421
• Royer R121
• Beyerdynamic M160
• Audiotechnica AT2035
• AKG C414

• Ibanez TS808
• Ibanez Nu Tube Screamer
• JHS PG13 Paul Gilbert Signature
• MXR Berzerker OD
• MXR Wylde OD
• MXR II Torino OD
• Mesa Flux Drive
• Mesa Grid Slammer
• Mesa Cleo
• Seymour Duncan 805
• BOSS SD1 TS808
• BOSS BD2
• Fortin Grind
• Marshall Bluesbreaker

Related Questions and Answers

Q: 1. Can this rig hold a canon c500 mark ii (or c300 mark iii)? with cinema lenses. Mostly for documentary use.

A: Yes, The Canon C500 II or Canon C300 mk II would be supported when using the PolarPro Pivot Shoulder Rig System.

Q: 2. Is the same rope replacement for all easyrigs models? (I mean vario 5, or cinema 3)

A: according to Easy RIg " This rope fits all models except Gimbalrig (800mm lower support bar) and MC-Rig (1000mm lower support bar)."

Q: 3. Can an Ikan 7 monitor be mounted on this bracket, or would it be too big or heavy?

A: Not sure. I have a smallHD 7 inch that works fine with it

Q: 4. I was at the 2015 NAB Show, and I'm almost certain I saw one of these with a Canon C100 Mark II mounted on it. Is that possible? Is there an additional plate needed for that? I don't remember seeing one, but just wanted to make sure before I pursued purchasing one of these.

A: I'm only familiar with it in the fs7.

Q: 5. Can I use a follow focus in this item?

A: For most follow focuses, you will need to add some kind of rod mount system to use them. Something like the ELE-LBP would work.

Q: 6. What is the height in inches, or cm, from the top to the bottom shoe bracket? There only seems to be information on the width and not the height

A: The height of this Bracket is 8’’ from top to bottom.

Q: 7. Support heavy rigs? like 20 25 lbs

A: Tilta does not offer a max payload for the Tilta Lightweight shoulder Rig. However it should support a 25lb rig. Also this STEADYGUM Shoulder Support with VCT solution supports up to 33lbs https://bhpho.to/3C4iLLG

Q: 8. can you place this on a tripod with the rig attached? Or, do you need to take it off to use a tripod?

A: Yes, the Tilta Lightweight Shoulder Rig (Black) can be mounted to a tripod depending on how far forward the shoulder pad is placed.

Q: 9. Is this metal or plastic?

A: The Godox VSS-R01 Smartphone Rig would be plastic.

Q: 10. Are the rods on this system threaded on the interior of the ends?

A: Yes there are threads on the Polar Pro Pivot shoulder rig system that allow you to extend the rods using the following https://bhpho.to/3w1pwuX