With the 52 & 67mm Lens Adapter, you can easily attach lenses and domes to your SeaLife SportDiver smartphone housing to capture wide-angle and close-up photography. The adapter attaches to the SportDiver's lens port and consists of a 67mm ring along with a 52mm insert ring. Other step-up and step-down rings can be used to accommodate various lenses. SeaLife suggests using wide-angle lenses with optical magnification between 0.5x and 0.75x for closer shooting distances while fitting the subject in the frame.

The adapter is made of hard anodized aluminum with 316 stainless steel hardware and can be adjusted horizontally and vertically so that it lines up with the smartphone's lens.

Supports 67mm & 52mm Lenses on SportDiver    Horizontal & Vertical Adjustment    Hard Anodized Aluminum Construction    316 Stainless Steel Hardware

• Attach 67mm and 52mm underwater lenses to the SeaLife SportDiver underwater smartphone housing.
• The lens adapter securely mounts directly to the SportDiver's lens port.
• Horizontal and vertical adjustment screws align the lens over the phone's intended shooting lens.
• Made with durable hard-anodized machined aluminum construction with 316 stainless steel hardware.

Related Questions and Answers

Q: 1. Can I attach this to my Nikon Coolpix P900?

A: Since the Nikon Coolpix P900 does not have internal focus you cannot use the Sensei 67mm Quick Clip Lens Hood.

Q: 2. Is the screw stainless, aluminum or brass?

A: The SeaLife Adapter for GoPro Camera' screw is aluminum.

Q: 3. Does the Aqua Pod Mini extend as far as the original Aquapod?

A: Maximum Height: 38"

Q: 4. I have a Tamron 28 75 g2, and its hood was falling apart. Will this one be okay for replacement?

A: Yes, Tamron 28-75mm f/2.8 Di III VXD G2 Lens (Sony E) has a 67mm front thread. Sensei 67mm Quick Clip Lens Hood clips on top of your lens front thread. If you have a filter on the lens verify for fornt threads on your filters, otherwise the lens hood won't stay on.

Q: 5. Will this fit and work properly on a Nikon 24-85 AFs lens (non vr version) and will it accept the Nikon 67 mm lens cap ?

A: The hood will screw in to the filter threads but you will not be able to use the lens cap. And the dedicated hood for the AF-S Zoom-Nikkor 24-85mm f/3.5-4.5G IF-ED (3.5x) is the HB-28. It is no longer made by Nikon and at this time we do not have one used.With that hood you can put it on reverse and use the cap on the lens.

Q: 6. Can you use a lens cap with this lens hood attached? What size?

A: Yes, it is able to attach with a lens cap.

Q: 7. Can you put a filter on the front of the lens hood? If so, what size?

A: The thread on the front is not a standard size and will not accept threaded filters.

Q: 8. This appears to be a 2-piece set. Is there a ring that screws into the filter threads of the lens, and the actual hood that locks on to the ring, boyonet-style? Thanks.

A: Yes there should be a rather heavy duty ring that screws into the filter threads on the lens and the filter will snap onto that ring. The best thing about this arrangement is that it is quick if you need to take it off occasionally. The downside is that it tends to move around in a circular direction while you're shooting and the longer part of the hood may get in the shot during wide shots.

Q: 9. Where is this product manufactured?

A: The country of origin for this product is Japan.

Q: 10. Can 67mm rubber lens hood be used in Sony FE24 - 70 mm. F4.0 ZA without Vignetting?

A: We have not tested this hood on that lens. However, our opinion is that most likely it will not vignette at the 24mm end. It may with a filter. One thing with a rubber hood, you can move it in or out and that often can solve problems. Here is a recommended hood that is metal. Sensei PRO 67mm Wide Angle Aluminum Lens Hood B&H # SELHMW67. And of course, the lens comes with the Sony hood. Sony ALC-SH130 Lens Hood B&H # SOALCSH130.