Generate tube-like distortion, smooth sustain, and superfat tones with the Behringer BASS OVERDRIVE BOD400, an overdrive pedal that supports the entire frequency range of your bass guitar, even 5- and 6-stringers. The pedal includes a 2-band EQ and a blend control, allowing you to dial in your best sound with the perfect mix of overdrive and your natural bass sound. The pedal is powered by a 9V battery (not included) or the Behringer PSU-SB DC power supply (not included).

Tube-Like Distortion and Smooth Sustain    Superfat Tone    Balance Control Blends OD with Dry Sound    2-Band EQ and Gain for Sound Shaping    Status LED for On/Off and Battery Check    9V Battery or PSU (Not Included)    High-Quality Bypass for Signal Integrity    1/4" TS Input and Output

• Get tube-like distortion, smooth sustain, and superfat tone
• This Behringer product has been designed to compete head to head with leading products on the market
• Unique Balance control to blend overdriven and dry bass sounds for maximum punch
• Dedicated Level, 2-band EQ and Gain controls for awesome sound shaping
• Status LED for effect on/off and battery check
• Runs on 9V battery or the Behringer PSU-SB DC power supply (not included)
• First-class electronic On/Off switch for highest signal integrity in bypass mode

The BOD400 features a musical 2-band EQ and dedicated Gain and Level controls. In addition, Behringer included a Balance control, which lets you mix the overdriven signal with your natural bass sound for superb clarity, punch, and extraordinary character. That way you can add the perfect amount of tube-like tone without sacrificing all of your precious low-frequency content.

Related Questions and Answers

Q: 1. I would like to know the delay between the audio signal and the signal you hearIs there a delay or not?

A: The latency is very minimal. MIDI Latency5 ms (E6) to 19 ms (E2), 32 ms (E1)

Q: 2. I am doing a Facebook Live broadcast. I want to run a direct signal from my board, M32r Midas or mr18, into my iphone with a stereo signal. Can I directly from my board to this and thento my phone or is there a better way for pristene sound? Thanks

A: The iRig is going to be the simplest and cleanest method to get audio from your board into your iPhone.

Q: 3. Hello is really possible to record stereo? I have tested SmartRig+ with 3,5 connector and adapter 3,5 to lightning. It is possible to record only mono mixed from two channels with this setup. Thanks for reply.

A: Yes, the SmartRig+ allows you to toggle between mono and stereo modes using a switch that is located between the two XLR-1/4" combo input jacks. The switch is labeled with "M" and "S" to indicate mono and stereo operation.

Q: 4. How much does the case and rack weigh empty?

A: The SKB iSeries 2317-14 4U Flyrack Case for Line 6 Helix / Kemper Guitar Processor and Foot Controller has a specified weight of 31.4 lb / 14.2 kg.

Q: 5. Does this work with ordinary PDF files?

A: I use it with mac iBooks and iScores and it works with pdf files

Q: 6. Hey! I have a Sennheiser MD 46 dynamic microphone. Do you know if the preamps in the linkflex-ad2 are good enough to boost this dynamic microphone? I would like to use the linkflex to connect the MD 46 to an iPhone (and possibly my good old Zoom H2). Would that work?

A: As previosly answered: 6249490Approved The Linkflex specs show up tp 20dB of gain. which may be enough gain, depending on your subjects volume level. One question is, how much electronic noise will be added to the signal? Another question is, how will the MD46 sound if you must turn the Linflex up to full level on its level control. A big part of how a microphone will sound, is the impedance of the mic pre (the Linkflex) amplifier. The noise spec is not listed in the spec sheet, so I would be weary of this. It may be a lot to include, but this is the reason these; Cloudlifter CL-1, are included in the signal chain with dynamic mics, to improve, not only gain, but performance... Comica Specs: Comica Audio LINKFLEX-AD2 Specs General In-Line Accessory Type Pre-Amplifier Gain Up to +20 dB Connectivity I/O 1 x 1/8" / 3.5 mm TRRS Male Output 1 x 1/8" / 3.5 mm TRS Female Headphone Output 1 x Combo XLR-1/4" TS Female Mic/Hi-Z Input Performance Frequency Response 20 Hz to 20 kHz ±1 dB THD+N 0.02% (2-Kilohm Load)

Q: 7. When does the units need to be charged? How long does charging take?

A: The Gemini GMU-G100 Wireless UHF Guitar System charges via its onboard Micro-USB connection on each unit and included USB cable. Specific charge times are not provided by the manufacturer.

Q: 8. Would this device work to take a call on whatsapp? To make a live broadcast by reporters/journalists? Thanks!

A: That would depend on if WhatsApp allows real-time audio monitoring through Lightning. It should, but you might want to contact WhatsApp's support to verify.

Q: 9. Does anyone know if it is possible to send a Line Level signal into this unit?

A: Absolutely YES. It has XLR & 1/4" combo and 3.5mm inputs, so for line-level choose the 1/4" or 3.5mm inputs and use the level controls to dial in the level you desire.

Q: 10. Can you use this for audio input on a live-stream?

A: Yes, the Saramonic SmartRig+ Di can be used to connect microphones and/or instruments for live-streaming audio.