This 67mm Magnetic Filter Adapter Ring is part of the Sensei Pro Magnetic Filter System, which can speedily attach and remove filters or polarizers without slowing down photo session workflow. Changing a filter to a polarizer or vice versa is seamless. Connect the 67mm Magnetic Filter Adapter Ring to any desired filter or polarizer and attach Sensei Pro's Magnetic Lens Adapter Ring to the lens. Now, the filter can be magnetically attached and removed from the lens in just seconds.

NOTE: The 67mm Magnetic Lens Adapter Ring is a required component and is separately available.

Magnetic Lens & Filter Conversion Set    For Lenses with 67mm Filter Threads    2 x Magnetic Filter Adapter Rings    Black Anodized Aluminum Construction

Related Questions and Answers

Q: 1. Will this fit and work properly on a Fujifilm 18-135mm zoom lens?

A: While we are not aware of the exact combination's compatibility, B&H # FU1813535WRL has the proper filter thread and focal length to work with this hood. It should work.

Q: 2. will this work on the t5i 67mm 18-135mm STM lens?

A: Yes, this lens hood is designed to fit on lenses with a 67mm filter/cap thread size and will accommodate zoom lenses such as this with a varying field of view.

Q: 3. Is this good to use on the Sony 24-70 f4? Doe it fit? Does it vignette?

A: Yes, the Sensei 67mm Quick Clip Lens Hood will fit the Sony 24-70mm F4 lens with the 67mm filter size. Using this hood should not cause any vignetting.

Q: 4. Will this work on a Nikon Coolpix P900???

A: I bought this for my P900, it screws on, but pops right off. I suggest spending a little more money on one rather than getting this one. The collapseable hood I purchased stays on fine.

Q: 5. will this lens hood work with the FUJIFILM TCL-X100 II Tele Conversion Lens?

A: Although it will physically fit, it is likely that you will see the edges of the hood in the images.

Q: 6. Will this work on the Canon SX50HS ?

A: You could use the sensei 67mm screw-on lens hood with the SX50 HS, though you would need the Canon Filter Adapter FA-DC67A (B&H# CAFADC67A): the SX50 HS doesnt have a standard front filter thread. You would be better off using one of the bayonet hoods designed for the SX50. They dont require an adapter.http://bhpho.to/1nn2qS6

Q: 7. Will this fit and work properly on a Nikon 24-85 AFs lens (non vr version) and will it accept the Nikon 67 mm lens cap ?

A: The hood will screw in to the filter threads but you will not be able to use the lens cap. And the dedicated hood for the AF-S Zoom-Nikkor 24-85mm f/3.5-4.5G IF-ED (3.5x) is the HB-28. It is no longer made by Nikon and at this time we do not have one used.With that hood you can put it on reverse and use the cap on the lens.

Q: 8. This appears to be a 2-piece set. Is there a ring that screws into the filter threads of the lens, and the actual hood that locks on to the ring, boyonet-style? Thanks.

A: Yes there should be a rather heavy duty ring that screws into the filter threads on the lens and the filter will snap onto that ring. The best thing about this arrangement is that it is quick if you need to take it off occasionally. The downside is that it tends to move around in a circular direction while you're shooting and the longer part of the hood may get in the shot during wide shots.

Q: 9. I have a Tamron 28 75 g2, and its hood was falling apart. Will this one be okay for replacement?

A: Yes, Tamron 28-75mm f/2.8 Di III VXD G2 Lens (Sony E) has a 67mm front thread. Sensei 67mm Quick Clip Lens Hood clips on top of your lens front thread. If you have a filter on the lens verify for fornt threads on your filters, otherwise the lens hood won't stay on.

Q: 10. Will this fit a 85 mm f/1.8 AF nikon lense?

A: This lens hood would work on the Nikon AF-S 85mm f/1.8 G.