Bring your overhead camera closer to the action with the Mini Pendant Cap Mount by Verkada. This mounting accessory fastens your Mini Series camera to the end of a compatible threaded pipe, available separately. Such mounting brings the camera closer to the area being monitored for increased detail. An aluminum alloy construction ensures long-term durability. The cap is compatible with the Verkada ACC-MNT-ARM-1.

For Mini Series Cameras    Mounts to 3/4" NPT Threaded Drop Pipes    Compatible with Verkada ACC-MNT-ARM-1    Aluminum Alloy Construction

Related Questions and Answers

Q: 1. Can I use this with the Aputure Ls60x? Can I also charge this battery using a usb?

A: Yes, the SmallRig VB155 Mini V-Mount Battery (155Wh) could power the Aputure LS60X light. Also, the Smallrig VB155 supports being charged with USB PD chargers, via the USB-C port on the battery. USB PD Charger idea: Xcellon Mighty Mini 165 65W GaN USB Type-C Charger (Black) BH #XCPDG165B USB-C charging cable: IOGEAR USB Type-C To USB Type-C Cable (6.6') BH #IOG2LU3CM12E

Q: 2. I just bought this and there is a small plastic case that comes with it. (not the big one that is holding everything) what is this little case for?

A: The photo on our website shows decals of memory cards on the small case. https://bit.ly/3jNCB1G

Q: 3. does it fit to the rsc2?

A: To fit this on the Ronin SC2, you will need a cold shoe mount with NATO rail clamp. Otherwise, the ANDYCINE Mini Shoe Mount Monitor Mount will fit any mirrorless/DSLR camera.

Q: 4. Will this fit Amaran 60D?

A: The Nanlite COB Cap with Bowens Mount for Select LED Monolights will be to short to sit properly on amaran COB 60x S Bi-Color LED Monolight. The Aputure does make spare accessories and I would suggest to reach out to the manufacture.

Q: 5. Are you able to mount the battery horizontally as well?

A: The v-mount plate of the NewTek TriCaster Mini Advanced HD-4 can be mounted to the rod block so that the battery is aligned vertically or horizontally, but it can not be mounted parallel to the 15mm support rods.

Q: 6. Will this fit on a GVM sd80d?

A: Yes, the Nanlite COB Cap with Bowens Mount for Select LED Monolights will fit on the GVM SD80D Bi-Color LED Monolight.

Q: 7. Does the tilt adjustment need to be fully tightened down to support a 7" monitor? If the tilt adjustment is left slightly loose, can the monitor be tilted with one hand while still remaining well supported (without falling forward)?

A: This well built and sturdy device has a great deal of "play" with most monitor configurations at approx. 7". One should be careful with any device that is larger than that.

Q: 8. This single suction cup mount appears to be the same one that attaches to the Fat Gecko dual suction cup mount to make it into a triple cup mount. However, the pictures for this single cup device do not show the sleeve needed to attach it to the dual cup mount. Does the single cup one come with the sleeve, or can it be purchased separately?

A: To be honest I bought the the single , double and triple but for the single suction no sleeves to be attached its only work as a single suction cup only

Q: 9. Will this work with Voigtlander lenses with the Leica M mount?

A: Yes, this should work fine with your Voigtlander lens with the Leica M mount.

Q: 10. HI, Is there a version for Nikon Z mount lenses?

A: Yes. please review the following item. Sensei Rear Lens Cap for Nikon Z Lenses BH #SELCRNZ • MFR #LCR-NZ https://bhpho.to/3wsXKYX