The Windjammer for Super-Shield from Rycote is a synthetic fur cover which is designed to fit over a medium Super-Shield pod to provide protection against extreme wind noise. It is handmade and designed to have little detrimental effect to the high frequencies in the audio being captured.

Protection against Extreme Wind Noise    Lightweight Basket Windshield System    High-Quality Synthetic Fur Cover    Configurable for Centre-of-Mass Balance

• Fits over large Super-Shield pod

Related Questions and Answers

Q: 1. I have the Rode NTG3B which is 10 inches. Should I get the medium or large for the Rycote Super-Shield Kit for Shotgun Mics. Which one would fit better?

A: RYSSKM is directly compatible with the Rode NTG3B.

Q: 2. Is there any way to switch out the cable to use with a mid-side mic like the Sanken CMS-50? Do you sell such a cable?

A: Yes, you can replace the cable that is included with the Rycote 010320 Super-Shield Kit for Shotgun Mics (Small). The Sanken CMS-50 Short M-S Stereo Shotgun Microphone has a 5-pin XLR output connector which requires a Y-cable that splits to two 3-pin XLR male connectors like the Sanken SC-532 5-Pin XLR Female to Dual 3-Pin XLR Male Adapter Y-Cable - 1' (B&H # SASC532), the Remote Audio 5-Pin Stereo XLR Female to Dual XLR Male Y-Cable - 18" (B&H # RECAXSTE), or the Sennheiser ACS5 5-pin XLR Female to Dual XLR Male Y Cable for MKH418S and MKE44P Microphones -6" (B&H # SEACS5). You can also make a custom cable yourself or have one made for you with the appropriate connector to fit the windshield and pistol grip.

Q: 3. this is good for MKE 600I still have ME67ME66What else do I need to purchase?It can be applied

A: To clarify: Modular 5 will accommodate only the MKE 600 and ME 66; Modular 7 will accommodate all three, but is larger than required for the MKE 600 in particular.

Q: 4. Can Sennheiser MKE 600 fit in this?

A: Hi there,It's not our official recommendation; however, you should (just about) be able to get away with an MKE 600 in the Super-Shield, Medium, since it's only 6mm over our recommended length. We would still recommend the Large, though!If in doubt, it might be an idea to bring the mic along to a dealer and try it inside the Medium, since everyone's needs are different.

Q: 5. Will the Rode NTG4+ fit inside this blimp (size medium)?

A: Yes it will. Just ensure that you position it properly on the mounts.

Q: 6. would this be a good choice for using the sennheiser mkh8050 or neumann km 185 outdoors?

A: Yes, this windshield would be a good choice for this application. Please note that it is not designed to be fitted over the mic itself, but rather fitted over a Cyclone Windjammer such as BH #RYCWSKS.

Q: 7. Will this fit the Videomic Pro+ ?

A: No, this Rycote Mini Windjammer is intended for use with a different mic. For the VideoMic Pro+, you can use the Rycote Mini Windjammer for Rode VMP+ (B&H # RY055470) or Rode DeadCat VMPR+ Artificial Fur Windshield for VideoMic Pro Plus Microphone (B&H # RODEADCATVPP).

Q: 8. Can this screw onto a boom pole? If so, what are the thread specs?

A: Yes, the Blimp can be attached to a boompole, threading size is 3/8"

Q: 9. Would this be the correct model for the Sennheiser MKH 50?

A: The Super-Shield Kit for Shotgun Mics (Small) from Rycote will accommodate several mics including the MKH-50. Rycote also recommends the Modular Windshield WS 2 Kit for a more robust solution.

Q: 10. I would like to remove the handle from this and mount it to a camera cage with a 3/8-16 or 1/4-20 screw. Would that be feasible by threading it through the hole the handle clamp screws through?

A: No problem grippper will attach to your rig as long as you have a 3/8 thread