Designed to fit perfectly with the 4 x 5 View Camera, this Intrepid 4 x 5 Lens Board measures 96 x 99mm and accommodates smaller, lighter lenses with a 34.6mm-diameter Copal #0 shutter.

Designed for Intrepid 4 x 5 View Cameras    96 x 99mm Lens Board    For Copal #0 Shutters (34.6mm)    For Smaller, Lighter Lenses

Related Questions and Answers

Q: 1. This is listed as an accessory for the ikan IK-RSR6 Hi-Hat Riser but I don't see how they connect. Wouldn't there need to be a 3/8ths stud?

A: The Alan Gordon Enterprises Hi-Hat and Low-Hat Mounting Board is not compatible with the ikan IK-RSR6 Hi-Hat Riser (6").

Q: 2. Can I put this on my EOS M50?

A: No, the Holga Lens for Canon DSLR Camera is designed for use with the Canon EF mount and an adapter will be required to use it on the Canon EOS M50.

Q: 3. 110 volt or 100 to 240?

A: 110

Q: 4. What lens comes with the camera?

A: The lens, the lens boards, and the Fresnel screen are not included with the Intrepid Camera 4 x 5 View Camera.

Q: 5. Hosa Technology GPP290 Monaural Male 1/4" Phone to Stereo Female 1/4" Phone Adapter Can the above adapter be used to insert headphones into the adapter re the Zedi 10 FX's "aux out" quarter inch jack? Would this, notwithstanding the need for a converter, to convert line level signal to headphones level signal, work? If headphones are inserted into the aux out jack directly, the result is audio in the left ear only.

A: First, let's make clear that headphone signal is line level and headphone outputs typically use a stereo connector. The aux output on the Allen & Heath ZEDi-10FX is sending a mono line level output signal via a 1/4" TS (mono) jack, so that is why you only hear audio through the left side of your headphones when you connect the stereo plug to the mono output. The Hosa Technology GPP290 Monaural Male 1/4" Phone to Stereo Female 1/4" Phone Adapter (B&H # HOAPMSPF) will convert the stereo plug on your headphones to mono and that will allow you to hear mono audio through both sides of you headphones (same audio through both sides) when you connect the stereo headphones to the mixer's mono aux output. If you need to connect two sets of stereo headphones to the ZEDi-10FX, a better option would be to use a stereo splitter connected to the mixer's headphone output. The Hosa Technology 1/4" Male to Two 1/4" Female Y-Cable (B&H # HOYCSPM2SPF) will allow you to connect two sets of stereo headphones without sacrificing tone, volume or stereo separation. If you need to accommodate more than two sets of headphones, the best option is to use a separate headphone amplifier connected to the mixer's headphone jack. The Polsen HMA-41 4-Channel Stereo Headphone Amplifier (B&H # POHMA41) or the Mackie HM-4 4-Way Headphones Amplifier (B&H # MAHM4) are good options for this purpose. The headphone amplifier will give each user their own headphone jack as well as an individual volume control to set the volume level for their headphones fas desired.

Q: 6. Does this interface enable the recording from the SDI input directly to the SxS card (no XDCAM disc)?Thanks

A: This updates the older version of the PDW-HR1 so that it can record FROM the SxS cards, However, it does not allow it to record TO the SxS cards.

Q: 7. Can this board be used with a Canon Imagraf 4100s?

A: No, the Canon imagePROGRAF Pro-4100S Printer does not have a straight paper path, and so is not able to print on the FUJIFILM Semi Gloss RC Board.

Q: 8. Can I use this on my non-digital Canon Rebel2000? It does use the EF mount.

A: Yes the Holga Lens for Canon DSLR Camera, will work on Canon EF mounts, and should be fine for a Rebel2000 with EF mount.

Q: 9. What is the screw size and thread gauge of the screws that come with this?

A: We connected with Alan Gordon about the screws included with the Alan Gordon Enterprises Hi-Hat and Low-Hat Mounting Board (Pre-Drilled with Screws). Moreover, please note that only Alan Gordon Hi-Hats are compatible with the board. The screws and nuts included are: Cap screw is 3/8 16 by 1 1/4" Hex nut 3/8 16 nut Washers 3/8

Q: 10. Does this come as pictured or with the white laminate?

A: It looks like our current inventory is in this standard finish for the Alan Gordon Enterprises Hi-Hat and Low-Hat Mounting Board (Pre-Drilled with Screws).