Connect your digital consoles, stage boxes, lighting consoles, and more with the GigaCore 10t Gigabit PoE++ Switch from Luminex. This fully AV-validated switch has eight 1 Gb/s PoE++ ports with EtherCON Neutrik connectors and is ideal for touring, theaters, or even houses of worship. Designed for demanding workloads, the 20 Gb/s switching capacity is further complimented by its 1 GB of RAM, which provides plenty of headroom for simultaneous transfers of high-channel audio counts, DMX data, and video streams.

With a focus on flexibility, the 10t is managed by the Araneo system management software, which allows users to direct web traffic and even leverage the redundant RLinkX capacities of the 10t line of switches. The single, half-rack design allows you to rack two units next to each other for easy setup, and the PowerCON TRUE1 Neutrik power connector gives you greater options for placement.

8 x EtherCON Gigabit Ethernet Ports    8 x PoE-Compliant Ports    20 Gb/s Switching Capacity    1GB RAM    Rack-Mountable Design    Araneo System Management    RLinkX Redundancy    Fully AV Validated    PowerCON Power Connectivity

Found on all GigaCore switches, the Araneo software can manage multiple switches on the network. Data streams and topology are visualized as are the port status of every GigaCore and has two modes (online/offline) for setup and operation. Online mode shows everything you need to know about the status of your GigaCore network. Offline mode lets you plan the complete network topology and GigaCore settings in advance.

Since every show or event can vary greatly, the built-in web UI allows you to adjust the settings in a way that best suits your needs. Assigning groups (VLANs) to ports, creating trunks, or adjusting other port and PoE settings can be done on the fly, and the status page gives you an overview of the complete switch at a glance. The toolbox page allows management of profiles and lets you upgrade firmware easily.

*IEEE 1588-2008 low jitter and hardware timestamping audio protocol compliance.

The flexibility of the 10t is further complimented by its silent design. Fans are speed-controlled to have minimal noise impact, which allows you to place the GigaCore in quiet environments like theaters and studios.

Related Questions and Answers

Q: 1. if I need to install this camera like 100 ft far from my switcher and the controller wich cables do I need to add to my cart?

A: Kopul Premium Series 3G-SDI Cable (100 ft) BH #KOVBBC4100 • MFR #VBBC-4100 https://bhpho.to/3oyvJeO

Q: 2. with this camera and joystick panel option.... can i get a long SDI cable to my video switcher, and control over standard {ethernet, cat xx) long cable for movement ?

A: While this camera does have an SDI output, the controller in this kit is not IP.

Q: 3. is it compatible with mixpre 10t ?

A: Yes, it is. Mine arrives today, and I will verify, but the documentation explicitly states that is is compatible.

Q: 4. Can this be mounted upside down on ceiling and have the Picture right?

A: Yes it can be and we have the AViPAS Ceiling Mount for Compact Avipas PTZ Cameras, BH #AVC80. https://bhpho.to/38dXcrR

Q: 5. If my computer does not have an sdi input how to I connect the the video to my hdmi input or usb, I just need it to stream for YouTube nothing fancy

A: You can simply connect the camera to your network by using the ethernet port on the camera and then receiving the IP feed on your computer with software e.i. OBS. If you use the SDI, you'll need to get an SDI capture device like BH #MA32070: https://www.bhphotovideo.com/c/product/1350328-REG/magewell_32070_usb_3_0_sdi_capture.html?sts=pi&pim=Y

Q: 6. Are there any joystick control compatible with this camera? Tks in advance!

A: The PTZOptics 4D IP Joystick Controller (GEN3) is a great option for this camera, BH #PTJOYG3. https://bhpho.to/39kXcFn

Q: 7. Is the IR remote the only way to control it? Is other software included for control over LAN?

A: Along with the IR remote you will also be able to connect this camera to your network and control it with PTZOptics 4D IP Joystick Controller (GEN3), B&H # PTJOYG3. This camera and the remote use Visca over IP protocols.

Q: 8. To use the sdi output is the power supply necessary? Or only with power supply via PoE

A: You should be able to use the SDI output however you power this unit.

Q: 9. Compatible with Canon EOS Rebel SL2?

A: Yes

Q: 10. Will the cameras 1080i / 59.94 SDI output resolution work with 1st generation of Black Magic ATEM switcher?

A: If you are referring to the original Blackmagic Television Studio Production Switcher then yes, it will work. That switcher required a 1080i59.94 setting from the camera, which this camera offers.