Protect your Canon EOS R5, R6, R5 C or R mirrorless camera and add a variety of accessories with this space gray Full Cage from Kondor Blue. The cage features an Arca-type quick release baseplate system for quick mounting and release of the camera and cage onto a rig. This full cage incorporates NATO rails, a shoe mount, and multiple 1/4"-20, 3/8"-16, and ARRI-style threads for additional accessory mounting choices.

This durable cage protects your Canon R5, R6, R5 C or R camera while maintaining access to its ports, slots, and controls. It features an integrated HDMI/USB Type-C clamp to protect the cables from pulling during operation.

Camera Cage for Canon R5/R6/R6II/R    Top Handle with Run/Stop Button    ARRI-Style Baseplate    501-Type QR Plate Included    2 x 8" PPSH 15mm Rods

Canon EOS R5, R6, and R mirrorless cameras

Rapidly remove the camera from the cage for stills, handheld, or gimbal use

The cage remains solidly mounted to the camera to prevent wiggle and allow for large setups

NATO rails on the side and top of the cage

A safety pin prevents sliding issues that plague shoe accessories

A cable clamp prevents damaging the micro-sized ports on the camera and losing signal

There are numerous 1/4"-20 and 3/8"-16 accessory mounting threads around the cage

3/8"-16 threads with locating pins on every side of the cage prevent twisting

The cage leaves open access to buttons, dials, cable ports, and battery/card doors

Protect the camera from a variety of drop angles

Related Questions and Answers

Q: 1. Does the mounting screw stay attached to the plate? I have a Kirk plate that the screw just falls out.

A: Yes, it stays attached.

Q: 2. Is there a way to add a Peak Design Anchor Connector to allow the use of the Peak Design Clutch?

A: The Peak Design Anchor Mount can be attached to the 1/4 20" mounting receiver on the bottom of the Falcam Quick Release Camera Cage Base V2 for Canon EOS R5/R6/R6 II.

Q: 3. Will this plate work with the Battery Griip? I don't see the hole in the bottom of the Grip for the pin that is in line with the tripod mounting bolt.

A: No, this plate is meant to work for body only.

Q: 4. Can this attach to the V1 cage to replace the older bottom plate, or is it for v2 cage only?

A: Yes, the Falcam Quick Release Camera Cage Base V2 for Canon EOS R5/R6/R6 II can replace the Cage Base for the V1.

Q: 5. Will this plate work with the Peak Design Anchors? I need a flat bottom so that the Camera can sit firmly on a flat surface.

A: Unfortunately, neither us nor RRS have more images showing a more detailed view of the bottom of the plate. Until we are able to inspect it physically, it would be hard to be 100% sure. At first glance though, there don't seem to be any loops or recessed areas that you would be able to loop the PD anchors.

Q: 6. Is the Kirk L Bracket QD System strap mount same as the one for RRS QD System? Thanks.

A: The QD System strap mount is the same on both Kirk and Really Right Stuff L brackets.

Q: 7. will this fit the new R6 MKII ?

A: Yes, the Kirk L-Bracket for Canon EOS R5 & R6 (BH #KIBLR5 • MFR #BL-R5) will fit the Canon EOS R6 Mark II Mirrorless Camera.

Q: 8. Does this fit the R6 Mark II?

A: The Really Right Stuff Base Plate for Canon EOS R5 and R6 Mirrorless Camera is compatible with the Canon EOS R6 Mark II Mirrorless Camera.

Q: 9. Can this be used on the Peak Design Travel Tripod?

A: Yes, the Peak Design Travel Tripod will accept this Kirk L-Bracket for the Canon EOS R5/R6.

Q: 10. Bought this plate and there is two small bosses on the bottom that don’t fit the camera holes??

A: Unfortunately, I am not sure what you mean by "two small bosses on the bottom" of the camera plate. In any case, the Really Right Stuff Base Plate for Canon EOS R5 and R6 Mirrorless Camera has a single built-in standard threaded 1/4"-20 male mounting screw on the plate which would screw into the female-threaded 1/4"-20 tripod socket on the bottom of the Canon EOS R5 or R6 Mirrorless Digital Camera. The plate may also have an accessory female 1/4"-20 threaded socket and a QD (Quick Detach) socket for an optional QD strap on the base of the unit, but it would connect to the camera via the 1/4" tripod socket.