Drive power to your system with the robust 1000W C1000 Gold ATX 3.1 Computer Power Supply from NZXT. Designed for high-end gaming builds and workstations alike, the C1000 boasts immense wattage to handle a variety of demanding tasks while balancing throughput, optimizing power and efficiency.

Equipped with a single +12V 1000W rail and meeting ATX12V version 3.1 compliance, you get ample power to operate your resource-demanding components. Thanks to the modular form factor, you can pick and choose the cables you need for your system, saving space and leaving ample room for airflow. Traditional 24-pin, 4+4-pin, and 8-pin motherboard connectors are included alongside the 12 SATA and four peripheral connectors for your storage drives and devices. Supporting graphics cards are three 6+2-pin PCIe connectors while one 16-pin 12VHPWR connector is reserved for high-powered NVIDIA 40 Series graphics cards, sending a dedicated 600W to the GPU.

1000W Single +12V Rail    135mm Fluid Dynamic Bearing Cooling Fan    Intel ATX12V Version 3.1    1 x 12VHPWR Connector    3 x 6+2-Pin PCIe Connectors    12 x SATA Connectors    4 x Peripheral Connectors    Modular Cable Design    80 PLUS Gold Efficiency

Backed by the 80 PLUS Gold rating, you can ensure the C1000 operates at maximum efficiency with up to 91.9% and 89.3% at half and full loads, respectively. This ensures that your energy and power consumption isn't wasted.

Inside the metal housing of the power supply is a 135mm cooling fan equipped with magnetic levitation bearings for a smooth and fast operation that keeps the capacitors well within thermal range. This fan operates at a max speed of 2300 rpm with 93.02 CFM airflow while retaining a low-noise level of 44.5 dBA at max load, ensuring enhanced cooling while remaining quiet.

Measuring 6.2-inches in length, the C1000 can easily fit in a variety of cases both big and small without sacrificing performance.

Related Questions and Answers

Q: 1. Does this product works with the Sony a7s ii ?

A: Yes this would work with the Sony A7SII.

Q: 2. will it work for D850?

A: Yes this can work with the Nikon D850.

Q: 3. Will this work with a Canon 5D Mark IV that takes LP-E6 batteries?

A: Yes, the GyroVu USB to Canon LP-E6 Dummy Battery Intelligent Cable with 3.1A Power Supply works with the Canon 5D Mark IV.

Q: 4. Will this Work with the Nikon Z7?

A: It is compatible with the Z7 as well.

Q: 5. Just bought this item to power my Sony a6500 and I plug it in and connect the dummy battery to my a6500 and screen reads "battery exhausted" and then shuts down. Am I doing something wrong here? or is this power supply a dud?

A: You should doublecheck that the connections are all tight and secure, including the power connection.

Q: 6. will this work with ? 1.skywatcher HEQ5 2. ZWO 1600 mono cooled 3. ASI 120mm - s 4. 2 dew shields

A: The PowerTank Lithium is compatible with the Sky-Watcher HEQ5. You will need to contact the other manufacturers for compatibility inquiries. Sincerely, Garrett at Celestron

Q: 7. Would this work with the Sony VPL-XW5000ES? B&H recommends it but I don't see how this attaches to the center mounting hole.

A: The center hole on the Gabor UPMP-1000B AccuGear Universal Projector Mount (Black), B&H # GAUPMP1000, is meant to fit an extension column. A projector, such as the Sony VPL-XW5000ES 2000-Lumen 4K UHD Home Theater Laser SXRD Projector, would attach to the 4 "arms" on the projector mount.

Q: 8. Will this Work with the Nikon MB-N10 Battery Pack?

A: Yes, it can work with that battery pack.

Q: 9. what’s the best way to keep this battery charged or uncharged?

A: The Celestron PowerTank Lithium should be kept at around 40-50% State of Charge to be ready for immediate use – this is approximately 3.8 Volts per cell – while tests have suggested that if this battery type is kept fully charged the recoverable capacity is reduced over time. The voltage of each cell should not fall below 2 volts as at this point the anode starts dissolving causing copper shunts to form which will cause an irreversible loss of capacity. Similarly lithium based batteries can be damaged by over charging which causes the cathode to decompose.

Q: 10. Works for Sony a5100 ?

A: The Sony a5100 is using NP-FW50 battery, so it should work. Sincerely, GyroVu Team