Streamline your installation process while also giving your system ample power with the Corsair RM850x SHIFT 80 PLUS Gold Modular Power Supply. Not only does the SHIFT allow you to pick and choose the cables you need for your equipment, but it also places Corsair's Type 5 Gen 1 micro-fit PSU connectors on the side, working alongside your dedicated cable management spaces for a more organized experience.

Offering up to 850W and built off the ATX 12V Version 3.0 standard, you are able to deliver ample power to your gaming-focused components with ease while balancing electrical loads. Modular cable design allows you to pick and choose which cables you need or want to use depending on your system's configuration, giving you more breathing room inside the case while reducing cable clutter. Aside from the standard motherboard and CPU cables, you also get an array of PCIe cables giving you a total of four connectors between two 6+2 connectors on two cables and two 6+2 connectors on a single split cable. For NVIDIA 40 series graphics cards, a single dedicated 12VHPWR cable is included that further reduces cable clutter. You also get 12 SATA connections and eight PATA connectors for storage drives and peripherals, respectively.

850W Total Wattage    ATX 12V Version 3.0    12VHPWR Cable    4 x PCIe Connectors    12 x SATA Connectors    8 x PATA Connectors    Modular Cable Design    Side-Panel Connectors    140mm FDB Cooling Fan    80 PLUS Gold Efficiency

The SHIFT incorporates a unique design that places the traditional PSU-based connectors on the side as opposed to the rear of the unit, giving you a clear view of your connectors and streamlining your installation process when working in cases with side-accessible cable management areas.

The ATX 3.0 standard demands a high level of reliability and power efficiency, meeting the 80 PLUS Gold certification, giving you up to 87% and 90% efficiency at full- and half-loads, respectively.

A low-friction, fluid dynamic bearing 140mm fan with Zero RPM mode support ensures your PSU runs cool while staying virtually silent when not under high load.

Built with 100% Industrial-grade, 105°C-rated Japanese electrolytic capacitors for unwavering power and reliability.

The PSU and cables will fit in any PC case that supports ATX PSU format and is at least 8.3" (210mm) wide. The PSU must also be accessible from the side when mounted in the case.

Related Questions and Answers

Q: 1. will rack ears alone support this unit's 50 POUNDS? seems like rails would be required to not damage the rack or equipment.

A: Yes, the rack ears that are included with the CyberPower CPS1500AVR Smart App Equipped Uninterrupted Power Supply BH #CYPS1500AVR are able to hold if properly secured. A rail kit is available separately if you prefer that. CyberPower 4POSTRAIL Rackmount Rail Kit B&H # CY4POSTRAIL

Q: 2. Will this work with the RS 4 pro?

A: The Tilta Power Supply Base Plate for Select DJI Gimbals is compatible with the DJI Ronin RS4 Pro.

Q: 3. What part number will slave trip this unit?

A: You need to get BH #SPPPFBA405 speedotron Sync cord adapter -converts male household to male phono plug, then get a wein L8 micro slave.

Q: 4. Will this work for BlackMagic Designs Mini Converters?

A: No, the following unit offers a 2.1mm barrel and will not work with the BlackMagic Designs Mini Converters. Please review the following item Blackmagic Design PSUPPLY-INT12V10W Power Supply for Mini Converters https://bhpho.to/3nPId0Z

Q: 5. I'm looking for an adapter to power up my Viltrox L116T LED Light. Would this one work? Thanks.

A: Not that we are aware of.

Q: 6. I had 2 other solutions somehow lose power (the battery symbol blinks) after a few days. Will this one maintain for days?

A: The Nikon EP-5B Power Supply Connector for Select Nikon Cameras (B&H# NIEP5B) can produce the same amount of power even when used for long periods. However, higher temperatures could cause an increase in impedance and therefore a slight reduction in voltage output from the MOSFETs in the power source used -- presumably an AC to DC transformer. As such, we'd recommend making sure to allow that transformer's heat to escape during use rather than, say, covering it with anything that might insulate it, leaving it in the sun, or otherwise preventing it from touching surfaces that have the potential to wick heat away from it such as a cool floor. Since something similar can happen to your camera (which has the potential to cause or contribute to this problem, too, even if no overheating is sensed nor warned about), you may also wish to leave the battery door of your camera open, the rear screen pulled or at least tilted away from the body of the camera, and your camera mounted to something that can serve as a heat sink such as an L-bracket, cage, or tripod. Shading the camera from direct sunlight is also helpful. This product may be mounted in the hot shoe and used for that purpose even in slightly windy conditions: Glide Gear Adjustable Hood Camera Lens Shade with 11" Friction Arm (B&H# GLLS100) https://bhpho.to/3t1BhCV

Q: 7. How much power do these draw? My studio is in a building with older wiring..

A: The manufacture does not list the draw exactly on the Speedotron 4803CX - 4800 Watt/Second Power Supply (120V). But that size/power of a pack needs to really be on its own circuit. And it needs to be at least 20 amp circuit. .

Q: 8. Is it possible to power the power supply base plate with RS3 Pro batteries (BH #DJRBG30G)?

A: The Tilta Power Supply Base Plate for Select DJI Gimbals is designed to be powered via a D-Tap and cannot be powered from the DJI Ronin BG30 Grip for RS 2 & RS 3 Pro Gimbals.

Q: 9. My Teradek 2 pin lemo to AC plug powers this base but when I hit the lock/sleep button the power cuts out. Insufficient voltage?

A: The Tilta Power Supply Base Plate for Select DJI Gimbals requires 13-17V DC power via the 2-Pin LEMO connection and the Teradek 2-Pin LEMO to AC Adapter Cable only supplies 9V DC. It would be recommended to use the included D-Tap to 2-Pin LEMO adapter with a battery with a 14.8V D-Tap port for proper function.

Q: 10. will this power adapter work for my dvr? https://amcrest.com/catalog/product/gallery/image/29576/id/389/ also, see other pics.

A: Yes, the Watson Pro 12V 2A Power Supply (2.1mm) is compatible to power your DVR.