Add chaos to your patches with the intellijel Noise Tools 1U, a versatile Eurorack module that provides an essential dose of randomness. At its core, Noise Tools generates pulses and a noise signal that are normalled to a sample-/track-and-hold circuit and a slew circuit. The Pulse output is switchable between a steady clock or a random flurry of gates. The module ships with a ribbon power cable.

Clock and Random Pulse Source    Adjustable Pulse Rate Control    Analog Pink and White Noise Sources    Analog Sample-/Track-and-Hold    Analog Slew with Adjustable Slew Rate    Includes Ribbon Power Cable

• Clock and Random pulse source with adjustable rate.
• Analog pink and white noise source with very accurate spectrum.
• Analog sample-/track-and-hold with very low voltage droop.
• Analog slew with adjustable slew rate.

• 22 HP Eurorack format module (1U)
• Maximum depth: 1.1" (29mm)
• Includes power ribbon cable with Eurorack power headers
• Power consumption: +12V: 30mA, -12V: 30mA

Related Questions and Answers

Q: 1. Does this need batteries?

A: No batteries needed. Works well. Recommend.

Q: 2. If you're going to run an extension cord for this, what should you use?

A: The Olympus ME-52W features a mono 1/8 connector and ships with a 3.3ft extension cable. To extend further a similar mono 1/8 male to mono 1/8 female cable would be required. Unfortunately we do not offer such a cable here at B&H currently.

Q: 3. If you are cascading 2 C1 Pro hubs and have 16 headsets can you assign as many headsets as you want to A & B group (eg 12 headsets on A and 4 on B group) Also if you have a master headset in addition to the the two hub system is it possible and relatively easy to unpair some of those 16 headsets paired to the hubs and pair them to the master headset instead? We’re in a situation where we will want to go back and forth from these 2 configurations. Sometimes wanting all 16 headsets on the 2 hubs and sometime wanting some of those headsets to be used at a different location with the master headset configuration

A: The pairing system for the Hollyland Solidcom C1 Pro-Hub8S ENC 9-Person Full-Duplex Wireless Intercom System with Hub (1.9 GHz), B&H # HOSCMC1PHB8S, is fairly straightforward. The master headset is paired with the remote headsets at the factory. For manual pairing and group switching, please consult the manual: https://bhpho.to/3WDhWE4.

Q: 4. Will this work with a standard mic input on a camcorder?

A: Yes - but only if the camcorder supplies plug-in power

Q: 5. Where ca I buy the C1 Pro HUB Base, is it the same as C1??

A: The Hollyland Solidcom C1 Pro-8S Full-Duplex Wireless Intercom System is compatible with the Solidcom C1 HUB, which can be found here: https://bhpho.to/3JfdKm1

Q: 6. Does this works in México?

A: The Hollyland Solidcom C1 Pro 4-Person Noise-Cancelling Headset Intercom (Double-Ear) works in Mexico, the United States, and Canada without issues.

Q: 7. Can this connect to a Clearcom Encore with the 2-wire jack?

A: Yes, you can connect to a 2-wire intercom system like the Clear-Com Encore to the Hollyland Solidcom C1 Pro-Hub4S ENC 5-Person Full-Duplex Wireless Intercom System with Hub (1.9 GHz). Page 11 in the manual for the Hollyland Solidcom C1 Pro-Hub4S explains how to set this up: https://bhpho.to/3ZDMEz6.

Q: 8. Can anyone confirm if the me-52w will work on a ps4 controller?

A: When you plug in. ..you are suppose to hear the oher people..plus control the mic ..but of you plug the specific microphone in question in..you will not hear the people. It will Only be a microphone. The supplied ear piece with microphone does two things... not one.BEST OF LUCK.

Q: 9. Does this microphone record stereo sound?

A: No:/

Q: 10. What's the difference between this one Noga Cine Arm DG Hold-It Arm B&H # NODG9014CA MFR # DG9014CA and this one Noga DG9038CA CineArm DG (Medium) B&H # NODG9038CA MFR # DG9038CA? They look the same!! I know one has a 3/8 instead of a 1/4 bottom. I'm using for a shogun flame..thank you guys!!

A: The DG9014 is threaded at both ends of the arm for 1/4-20 thread attachment while the DG9038CA is 1/4-20 top and 3/8-16 bottom.