Enhance the capabilities of your SliderPLUS v5 PRO and unlock its creative possibilities with this Vertical Module from edelkrone. The very sturdy and innovative device, when used with the separately available Motor Module, allows full vertical operation of your slider starting at 10° increments up to 90° even when employing heavy cameras and gear with a payload of up to 27.5 lb. Five constant-tension springs transform the SliderPLUS into a virtually weightless system and enable smooth and reliable vertical operation.

The added versatility facilitates multiple approaches to your specific style of operation, including fly-over and fly-under modes. The unit itself weighs approximately 2 lb but can compensate for more than 22 lb. An L-bracket is included for mounting, along with a manual engagement knob and a tension adjustment screw for the optional Motor Module.

Adds Vertical Orientation to SliderPLUS    Works at 10° Steps at up to 90° Angle    Constant-Tension Springs    27.5 lb Weight Capacity    L-Bracket Included

Vertical Module mounts under the SliderPLUS v5 PRO easily and comes with an L Bracket to level your camera or head. (Requires separately available Motor Module, not for manual use).

The module offers five levels of spring tension to accommodate different equipment weights and is easily adjustable by attaching the necessary number of rings to the side of the SliderPLUS.

Vertical Module utilizes an axis knob that allows for quick angle adjustments on the go.

Vertical Module enables SliderPLUS to capture time-lapses at any slide angle.

The combination of the Vertical Module and SliderPLUS v5 PRO ensures that you will never feel limited in your camera movements ever again.

Related Questions and Answers

Q: 1. Where can you purchase replaceable magnetic belt clip and foldable legs?

A: You need to contact Edelkrone support, directly. They offer free spare parts to Edelkrone users.

Q: 2. Can you invert for top down motion shots?

A: Yes, you can invert the slider for top down shots. At this time Edelkrone does not have a rig for mounting upside down, so please be careful when constructing your own.

Q: 3. Can this handle a pocket 6k pro with regular battery and 24-70 lens?

A: Yes, the edelkrone SliderPLUS v5 Long supports up to 40 pounds.

Q: 4. Can I use the motorized slider for a 90degree vertical lift with a Sony A7iii +50mm kit lens?

A: When paired with the Slide Module v3, the SliderPLUS v5 PRO Long can be mounted on a tripod at an incline of up to 22.5° with up to 5.5 lb loads. The SliderONE Pro is capable of doing inclined shots up to 90 degrees. You can check out SliderONE Pro page for the recommended weight load on various incline angles.

Q: 5. Does anyone know if it will fit the Edelkrone SliderPLUS PRO XLarge?

A: Yes it will.

Q: 6. Can I use a Syrp Genie to power this slider?

A: It cannot. You would need to use an edelkrone specific product which is the Slide Module v3 BH #ED81228. https://bhpho.to/3sC4r6N

Q: 7. Will the SliderPlus V5 work with a Canon C200 and a 70-200 lens? That should be around 7pounds. And this slider says that it supports 10 pounds.

A: Yes, you will be able to use the Canon C200 with a 70-200mm lens on the edelkrone SliderPLUS v5 Long. I do recommend that you use a tripod that is strong enough to support payload when the camera reaches the end of the slider. We offer some support solutions that might make this easier if you notice that the payload is too much for the slider to handle at its ends. Check out the GVM Aluminum Slider Support Rods (Pair).

Q: 8. Does this common with the motor?

A: No, it does not come with a motor.

Q: 9. What is the max payload in order to allow the maximum travel distance of 90cm?

A: When used on a tripod this system can slide 2.9' with 20 lb Payload. When put on the floor or another flat surface the system only goes 1.4' but then has 40 lb Payload.

Q: 10. Does this slider accommodate mounting a Manfrotto 612 Nitrotech flat base head?

A: yes it does