The 40.5mm Okko Lite CPL Filter allows you to filter out unwanted reflection from water, snow, or glass, and eliminate haze for crisper images to capture rich, clear shots in challenging bright conditions. This affordable, adjustable filter allows you to control polarization for color saturation and greater contrast. Featuring a glass thickness of 2.4mm and an optical density of 0.3.

Aluminum Frame

Okko Lite CPL filters reduce haze, allowing you to achieve greater color and tonal saturation for clearer images with better contrast.

Constructed from high quality, matte black aluminum and designed for use with the lens cap attached.

Ultra-thin frame minimizes the vignetting effect on wide angle lenses.

Related Questions and Answers

Q: 1. How can I buy replacement studs for this? I have lost them for two of these units and can’t use without them.

A: There are many variations of them (they're also known as spigots) that we carry here, but these would be the exact item as a replacement piece: https://bhpho.to/2LRjzMM

Q: 2. Is this the sort of mount I would use to hold a profoto a1? Newbie here. Thanks.

A: I have a few of these that I use with Nikon Speed Lights with Pocketwizards and they work well. They lock in place well and I've even had them handle a bit of wind without shifting. I don't know how much heavier the Profoto lights are though...

Q: 3. Is the honeycomb grid and hood diffuser included in this set? If not, do you have anything that will work with this set?

A: A softbox is included for each head in this kit. However, there are no grids available to fit them. For grids to fit the lamp heads using a reflector, you may consider the Elinchrom Reflector and Honeycomb Grid Set, B&H # ELCGS8.25 . https://bhpho.to/36ARezX

Q: 4. Can this unit accommodate a Sony HDR-CX405 HD Handycam with a Vello CB-600 Straight Flash Bracket attached? How about this same unit attached to a Canon PowerShot ELPH 180 Digital with the straight bracket.?

A: Yes, The Lowel Go Lite Compact LED Light would work with standard shoe adapters like the Vello 550 or other straight bracket models. Vello 550 link https://bhpho.to/39hOk9e

Q: 5. Will this work with my Godox AD200 where I can screw the strobe to the top and just pop an umbrella in? Sort of like the one that comes with the AD200, but made of metal? Thanks.

A: It will work with a AD200. Its much stronger than the little plastic mount.

Q: 6. Can this adapter be used to hold an Alienbee and 7' parabolic umbrella?

A: Yes this adapter can be used to hold an Alien Bees monolight and a 7 ft Parabolic Umbrella.

Q: 7. How much weight load can carry in 45 degree position?

A: Your light stand will tip over before the swivel will slip. I'd say it would take 10-15 lbs or more, depending on how severely you wanted to tighten the handle. These are plenty tough for use with portable strobes.

Q: 8. How do you keep the modeling lamp on. As soon as I take a photo, the modeling lamp goes off. I'm using the Elinchrom EL19366 Skyport Transmitter?

A: Hi,If you check your instruction book you will see how to control the modeling lamp.Here is the item you are inquiring about.Setup Visual-Flash-Control (VFC) modeProportional modelling lamp setup (PMS) Enter VFC setup :1. Press Prop push button for more than 2 seconds, until the display shows F.X (X is 0 or 1) toenter into the Modelling lamp setup menu.2. Use the Flash-Power up and down button to change setting:- F.0: Visual-Flash-Control = OFF. Modelling lamp remains ON after flash.- F.1: Visual-Flash-Control = ON. Modelling lamp switches off during recharging.3. The display switches back to normal mode after approx. 4 seconds if no button is pressed. Thesettings are automatically stored.4. Standard setting is F.0, VFC = OFFI hope this helps.Regards,Will H

Q: 9. I had previously ordered this and it came with an EL-Skyport Speed Transmitter. Does it still include this remote trigger?

A: Unfortunately, a transmitter is not included with the Elinchrom D-Lite RX One Flash Head. A compatible option is the Elinchrom EL-Skyport Transmitter Plus, BH # ELSTP. https://bhpho.to/3c95qbf

Q: 10. Where is the Minox X-Lite made?

A: The Minox 8x26 X-Lite Binoculars BH #MI8X26XLB • MFR #10009 are made in China