The DWU760-iS 7150-Lumen WUXGA Laser DLP Projector from Christie is a flexible and cost-effective option for small-to-mid-size spaces in corporate and educational institutions. The omnidirectional design allows it to be installed in any orientation, and the laser light source frees your organization from lamp replacement and frequent maintenance. The projections it offers are brilliant and in HD, with 7150 ISO lumens and a 1920 x 1200 resolution. That's bright enough for even fully lit locations. If you need something for larger spaces, the DWU760-iS can use built-in Christie Twist and support for Christie Mystique Lite to warp and blend its image with up to 6 other projectors.

Brightness of 7150 ISO Lumens    WUXGA 1920 x 1200 Native Resolution    Motorized Zoom, Focus & Offset Lens    1.25 to 2.0:1 Throw Ratio    Warp/Blend with Christie Twist Built-In    Supports Christie Mystique Lite    Project from Two Sources for PIP & PBP    2 x HDMI & 1 x VGA Inputs    Remote Projection Over HDBaseT    DICOM Simulation Mode

Both Twist and Mystique Lite allow you to join this projector with others, warping and blending images into a larger experience. Christie Twist is built-in and can blend and warp with up to 6 projectors and up to 81 grid control points. Christie Mystique Lite is optional and supported, offering automatic blending of up to 3 projectors with camera-based alignment.

Simultaneously project two video sources for picture-in-picture or picture-by-picture for enhanced virtual video conferencing.

Project content locally by connecting a laptop, Blu-ray player, or other device to the DWU760-iS's two HDMI or single VGA inputs. You also have the option of remotely accessing content over a local network via HDBaseT and a single (optional) Ethernet cable. This HDBaseT connection can also be used to remotely control the projector if needed.

DICOM simulation mode offers advanced grayscale image reproduction, which is ideally suited for examining x-rays and other medical scans.

Activate Eco Mode to reduce the brightness by 50% and save energy, run quieter, and extend the overall lifespan of the projector.

• Motorized zoom, focus, and offset lens
• 1.25 to 2.0:1 throw ratio
• 20,000-hour laser light source lifespan
• Supports 24/7 operation
• IP5X-rated dust-resistant optical engine
• Full HD 3D support via 3D Sync in/out
• AMX and Crestron control system support
• TAA Compliant

Related Questions and Answers

Q: 1. Can it be set to only trigger if the subject is moving faster than say 20mph?

A: Unfortunately, the LV5 cannot be set to trigger based on a specific speed of the subject in motion.

Q: 2. How precisely do you have to line up the laser? We've tried a similar product but it's so picky that even a strong wind can push it far enough out of alignment that the camera will not trigger.

A: The subject will need to be precisely aligned with the trigger.

Q: 3. Can the divider be removed?

A: The divider included with the JELCO JEL-616CB Padded Carry Bag for Projector or Printer (B&H # JEL616CB) may be removed.

Q: 4. Hello I just want to now if this product its good for splash photography,do I need and other cable or accesorie and how can I connect the device to a canon 5ds? thanks

A: Yes, this would be a good product for splash photography. You would not need additional cables to connect this to a 5DS.

Q: 5. Can I use this for Sony A7rII and Sony A9?

A: This is the cable: BH# VERCCS235

Q: 6. can it be tripod mounted ?

A: There is no built-in female bushing that can accept a 1/4' -20 standard tripod threaded male stud.

Q: 7. this speed light works on sony camera A6300 and A6400..??

A: This is a transmitter and laser trigger system. No flash is included. It will work on a Sony A6400 but it will also depend on which flash you wish to use with it.

Q: 8. Where do I put the image i want to trace?

A: Hey Joey, I just got an email from B&H asking to help answer your question. We have set ours up and tested it and it seems to work well. There is a opening underneath, where the mirror and light bulb go. Lay your image on your flat surface, and possibly under a small pane of glass to hold it down flat. Position the projector with the opening on the bottom directly on top of your image. I have a 100x equivalent CFL bulb in ours. In a darkened room it should work fine. Also the front tube for focus, the instructions say turn to change focus, but really what you do is slide it out or in depending on the throw length to your canvas or wall you are projecting onto. Hope this helps

Q: 9. which cable should I buy to connect this device to Canon EOS 7D mark ii (needs to be at least 20 feet long)? Thanks.

A: The LV5 has a 3.5mm port. The Canon 7D Mark II has a 3-pin shutter release. The proper cable would be the Vello 3.5mm shutter release cable for Canon 3-pin. B&H # VERCCC235. But this is not 20' long. Very soon Vello is releasing a 33' extension cord for this cable. In the meantime, the Canon 33' extension cord will work. B&H # CAET1000N3

Q: 10. Will this attach well to my Velbon tripod's head?

A: The Manfrotto 183 Aluminum Projector Platform will mount to either a standard 3/8 or 1/4 screw. Just be aware of the weight limit of the tripod you use.