The black C3110-126 Two-Way Passive Speaker System from RCF features Constant Matching Design technology for optimal transition between the high frequency horn polar pattern and the low frequency woofer directivity. The horn can be rotated, allowing the loudspeaker to be installed either vertically or horizontally. The high-frequency transducer in this system is a 1" compression driver with 1.5" voice coil for smooth, wide dispersion. The low-frequency transducer is a 10" woofer with a 2" voice coil for low frequency signals.

The system includes a high-level crossover network that features the LICC (Low Impedance Compensated Crossover) that offers delay reduction, reduced phase shift, and superior transient response. Dynamic high-frequency driver protection is accomplished with the Active Mosfet Compression Driver Protection System (AMCDP) that complements the driver power curve.

The cabinet is made of Baltic birch and is equipped with top and bottom multiple plates for either wall or suspended mounting with chains. The steel front grille is protected with a double layer polyurethane fabric. Connections are made through two Neutrik Speakon NL4 connectors (audio input and parallel link output). This two-way passive speaker system suitable for use in permanent installations such as main reinforcement in small spaces, high-level AV playback, zone delay and fill systems, and under balcony installations.

10" high-output woofer and 1" compression driver

120° x 60° CMD (Constant Matching Design) constant directivity horn

Rotatable horn for horizontal mounting

Trapezoidal enclosure made of 15mm birch plywood

HF driver with Active Mosfet Compression Driver Protection (AMCDP)

Low Impedance Compensated Crossover (LICC)

Rigging inserts: 8 x M8 (rear), 2 x M10 (lateral)

Two 'multiplates' (top and bottom) for either wall or suspended mounting with chains

Installation points on rear panel

Easily rotatable front RCF logo

Related Questions and Answers

Q: 1. Is there an aux input that would connect to my MP3 Player?

A: Unfortunately there is not. These are passive speakers so they would be useless to you for an MP3. You will need powered monitors with a 3.5mm input for MP3.

Q: 2. Can I connect a separate tweeter system to this speaker such as the Pyle Pro PAHT7 6-Way DJ Tweeter System?

A: A separate tweeter system cannot be connected to this P.A.speaker. The end-user does not have access to its crossover network.

Q: 3. if theses speakers were enclosed within a cabinet, what would be the box dimentions, wideth, height, and depth ?

A: These speakers are designed to operate properly in an in-ceiling installation. They should not be set into a baffle or enclosed box.

Q: 4. Does it come with two speakers or one

A: This is a single speaker cabinet.

Q: 5. Can I connect a subwoofer to the speakers directly Thks

A: No. The JBL SRX815 15" Two-Way Bass Reflex Passive System is a passive speaker, so it needs to be connected to a power amplifier. Depending on the subwoofer you select, if it is passive, it will also need to be connected to a power amp, while an active speaker has the amplifier built-in. If you are using a mixer, the mixer's output will connect to the input on the power amp(s) and the speakers will connect to the output from the power amps.

Q: 6. Hk audio Linear5 -112 F is fit for idol pro IP-300 digital amplifier

A: Yes, the HK AUDIO LINEAR 5 112 F Passive Two-Way 12" 1000W Professional Loudspeaker can be powered by the IDOlpro IP-300 Digital Amplifier.

Q: 7. Does it fit the RCF ART735A Model?

A: The ART COVER 715 will fit the ART 735A speaker.

Q: 8. what amplifier would work well for running 2 sets of these?

A: Any stereo amplifier with power rated at 4 ohms load, and with connections for two sets of speakers. Or, any cheap Home Theater receiver, with one set connected as front channels, and other set as back channel, and surround mode set to All Channel Stereo , or 4 Channel Stereo . In speaker setup set center channel and subwoofer to none . Since it is multichannel amp, Home Theater receivers don't need to be capable of driving 4 Ohms loads.

Q: 9. Can you plug it in in a Hercules 4mx

A: Yes - via the speakers 1/4 mono input. Hercules offers 4x mono connectors in '' jack format, to connect to a public address amplifier or speakers. Keep in mind that this speaker needs an amplifier to power it.

Q: 10. Can I simply hook these speakers directly to my computer or do I need to get other things?

A: This is not what you want. However, a really GREAT product that is getting a lot of note lately is this one.https://a href= http://www.bhphotovideo.com/c/product/1019177-REG/behringer_mpa40bt_pro_all_in_one_portable_pa_system.html target= _blank www.bhphotovideo.com/c/product/1019177-REG/behringer_mpa40bt_pro_all_in_one_portable_pa_system.html/a It will give you several ways to get computer audio into it, plus you can take it with you and use it for a PA, a jam box, etc. It lasts almost 12 hours on a charge of its internal battery. DYNAMITE product.