The brushed brass SF6-CPT-FF 6" Poke-Thru with Cover and Sub-Plate Set from FSR is a complete SmartFit fire rated floor box assembly.The Furniture Feed series Poke-Thru includes a 6" floor fitting, 2" conduit fitting for data and AV, a 3/4" conduit fitting for power, a Furniture Feed cover style assembly, and a junction box. This Poke-Thru cover has two holes to "feed" the cables through, and up into a piece of furniture, such as a table leg, etc.

The SmartFit series features recessed mounting bracketry to accommodate a wide assortment of power, data and audio video connection options.

All Fire-Rated Poke-Thrus are Buy American compliant.

Furniture Feed Cover Style Design    Fire-Resistant for 2-Hours    ADA Compliant Flange Height    Power Wiring Junction Box Included    Cover Loaded Rate at 1000 lb    ULC and cULus Rated    Buy American Compliant

2-Hour fire rating

Power wiring junction box included

Drop down cable access doors to reduce trip hazards

NEMA WD6 device spacing

ULC and cULus rated

Related Questions and Answers

Q: 1. what are the exterior dimensions?

A: The exterior dimensions of the Gator Elite Series Furniture Desktop Studio Rack are 21 x 14 x 6". The interior dimensions are 19.13 x 13.25 x 4.5" and the weight is 16 lbs.

Q: 2. Will this sub-flash work on the previous version of the Godox V1?

A: No, the Godox Sub-Flash for V1Pro will not work original Godox V1.

Q: 3. Is this connector Size D?

A: Yes, it fits a standard, D size panel cutout, same as an XLR connector.

Q: 4. There are two sides of adhesive - does it stick to the mat and mat board?

A: You apply these strips to a backing board with their adhesive tape -- for your purposes the adhesive tape is 1-sided, being already attached to the firm plastic strip.The adhesive doesn't cover the full width of the plastic strip; it leaves perhaps 1/5 of plastic free to act as a trap for the item being mounted. There is no adhesive in direct contact with the mounted item's surface.This is ideal for use on a backing board where glass and/or matting will keep the artwork from falling out of the strip's thin rim of plastic. It wouldn't work for a large paper item which lacked a glass in front -- the paper's weight would pull it out of plastic edges, I suspect. The role of this is to prevent artwork from shifting around after it matted and framed.Note that the adhesive holding the mounting strip is outside the dimensions of the artwork: the backing board needs to be around an inch wider than the artwork to have room for the strips.

Q: 5. Will this fit my YASHICA Electro 35 GS? The rewind knob is right next to the shoe, and this seems to lay pretty flat against the top of the camera. Is there a better option for one with a knob like that?

A: It looks like the TTArtisan Meter will not fit on the Yashicha 35 GBS because it would cover some of the camera's buttons. You can use a not hot shoe mounted Light Meter, such as this one https://www.bhphotovideo.com/c/product/1390250-REG/sekonic_401_305_l_308x_u_flashmate_light_meter.html.

Q: 6. Does the mentioned plastic strip go under or over the photo print? I have used positionable mounting adhesive in the past, are ?

A: When using the Lineco "See Thru" Mounting Strips, the plastic strips will go above, below, and on the sides of the photo print in order to cradle it so it is ready to be framed.

Q: 7. Does it comes in pairs?

A: Correct. This is a pair of replacement fasteners.

Q: 8. Why are you selling this sub-flash as a separate item to bundle with the Godox V1Pro when one is already included?

A: Due to its detachable feature as well as its small size, an owner of the Godox V1 Pro may lose this accessory during one of their photoshoots. If this were to occur, a replacement is available.

Q: 9. Can these strips be used for mounting 13" x 19" prints?

A: Yes, you can use the Lineco "See Thru" Mounting Strips - Pack of 60 to mount a 13" x 19" print.

Q: 10. what type of wheels kind I use?

A: The Gator Elite Sidecar comes with the optional wheels included. They are not sold separately.