The LUCIA PGI-72 Chroma Optimizer Ink Tank from Canon is compatible with the PIXMA PRO-10 Printer. It features pigment-based ink and Canon's FINE (Full-photolithography Inkjet Nozzle Engineering) technology which ensures accurate ink placement.

For the PIXMA PRO-10 Wireless Professional Inkjet Printer

Related Questions and Answers

Q: 1. Is this a good back drop support for photo booths that require either paper, cloth, or any material back drop? Also how do you attach the seamless paper roll to it?

A: Yes. This will accommodate both paper and material. The paper has a hollow core. Run the cross rod through it. Buy some pony clamps to prevent the paper from unraveling. A variety of clamps are in the accessory list for this background support.

Q: 2. Canon E-72 II 72mm Lens Cap - does this cap fit the 35mm 1.2 Canon lens?

A: No. The following unit will need a 67mm lens cap. Canon E-67 II 67mm Lens Cap BH #CALC67 • MFR #6316B001 https://bhpho.to/3PwlvWi

Q: 3. Are these muslins designed for 24' width or 24' in height (to be used as a wall to floor seamless)?

A: The sown in rod hanging looped over part of the fabric is on the 10' side. So, these are designed to hang on the rod with the 10' width. They then fall down 24' and drape onto the ground. You could also use spring clamps (#2 grip clips) to hang the fabric in any orientation you'd like. For example you could clamp the fabric so that it's 24' wide and 10' tall if you like. But it is designed to hang on the included rod and stands in a 10' wide 24' tall orientation... and since the stands only go up so far... there is quite a bit of overflow fabric that you can put on the ground.Hope this helps!

Q: 4. Are these background flame retardant?

A: No, neither the Impact Muslin Background - 10 x 12' (White), B&H # IMBGW1012, nor the Impact Muslin Background - 10 x 12' (Black), B&H # IMBGB1012, included in the Impact Background System Kit are flame retardant, and they should not be used around or near open flames or without proper fire extinguishing equipment nearby.

Q: 5. What is the total width between the outstretched stand legs when the bar is set at 12' ?

A: Not sure if you are referring to the distance between the farthest points on each leg or the length of the bar. The stands are adjustable to a degree, so you can improve support. I would say that if you want the legs fully extended that you leave 16' of room, but you could get away with 14-15' if you had to. Just remember that it will not be as stable.The bar itself is 12' long and supports 12' muslin and 11' seamless paper. Heavier fabric will cause the middle to bow slightly, so I would recommend when using a heavier fabric that you extend the legs fully.

Q: 6. Is it machine washable?

A: Yes, the Filmcraft Studio Blanket is machine washable.

Q: 7. Will this fit a 35mm f1.4 version one?

A: Yes.

Q: 8. How do you make the bars into the 6' across the top?

A: The top bar comes in three separate sections which allow for you to make it short or long. The whole setup comes apart easily and goes inside a nice little storage case. Best bang for your buck.

Q: 9. Will this work a cannon compact photo selphy cp910 printer . ?

A: Yes, this works with the CP910. It also works with the CP780, CP900, and CP1200 as well.

Q: 10. Are the width and height adjustable for this item?

A: The height is easily adjustable since it uses standard light stands. The width can be set to three values. The crossbar consists of 4 segments of 3 foot tubes. You can use 2 for 6 ft wide, 3 for 9 ft wide or all 4 for 12 ft wide..