Bluetooth Receiver With Rca Output For Car Audio

Rdl Db-tpr3a Active Triple Pair Xlr And Rca Stereo Audio Output Over Rj45 Receiver Module (black)

Product Code: ga174400
Availability: In Stock

$757.08 $1,082.62

Qty

0 reviews Write a review

Description
Reviews (0)

The DB-TPR3A Active Triple Pair XLR and RCA Stereo Audio Output over RJ45 Receiver Module from RDL is a three-pair audio receiving module compatible with RDL Format-A twisted pair products. The DB-TPR3A features a black front-panel laminate. The DB-TPR3A module features an XLR audio output and two RCA phono jack outputs, one for the left channel and one for the right channel. The audio signal received from pair A of the RJ45 input jack feeds the XLR audio output jack. The output level from the XLR jack is set to either Mic or Line level during installation using a rear-panel switch. The audio signals received from pairs B and C of the twisted pair cable are buffered to drive the RCA output jacks at the standard -10 dBV consumer level.

The DB-TPR3A module can access signals from all three cable pairs, and additional receivers may be connected to the same twisted pair feed. The bridging input circuits used in all Format-A twisted pair receivers allow connection of up to 10 receiver outputs for each cable pair. The DB-TPR3A can be powered directly from a 24 VDC power supply using the rear-panel detachable terminal block. Local power connected to the module is also fed to all connected remote modules.

The DB-TPR3A can be remotely powered through the twisted pair cable from any other module, signal distributor or RDL power inserter connected to the same twisted pair cable. Module power is indicated by a front-panel LED. This module is designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect external equipment. The DB-TPR3A model can be mounted in RDL WB-1U and WB-2U wall boxes, or in standard U.S. electrical boxes.

Parameters
Input Connections	RJ45 Format A Single Pair Used (2): B (Left); C (Right) Format A Output: RJ45
Output	Balanced: 150 ohms Unbalanced: 100 ohms
Output Connections	2 x RCA Phono jack 1 x XLR (balanced Mic or Line)
Output Level	XLR: -45 dBu Mic or +4 dBu Line Level, switch-selectable on rear panel RCA phono: -10 dBV
Frequency Response	10 Hz to 50 kHz (± 0.1 dB)
THD & Noise	< 0.005%
Noise	Below +4 dBu: < -90 dB
Crosstalk	< 90 dB (1 kHz) < 75 dB (20 Hz to 20 kHz)
Headroom	Above +4 dBu: > 18 dB
CMRR	> 80 dB (50 to 150 Hz)
LED Indicator	Power In, blue
Power Connections	1 x RJ45; detachable terminal block
Power Requirements	24 VDC @ 45 mA plus connected loads
Ambient Operating Environment	32 to 131°F (0 to 55°C)
Minimum Depth	Mounting Box Minimum Depth: 2.4" (6.1 cm)
Dimensions	1.6 x 4.11 x 1.89" (4.8 x 4.06 x 4.8 cm)
Weight	0.245 lb (0.11 kg)
Packaging Info
Package Weight	0.39 lb
Box Dimensions (LxWxH)	4.9 x 4.6 x 2.3"

Balanced Mic or Line Level XLR output

Switch-selectable output level on rear panel

Two unbalanced -10 dBV Phono jack audio outputs

XLR from Pair A; L from Pair B; R from Pair C

Remote powering through twisted pair cable

Fused local power feeds all connected modules

Local power input on terminal block

Blue LED indicates module is powered

Utilizes all three Format-A pairs

Active Balanced Circuitry

Related Questions and Answers

Q: 1. I want to understand pairing with this. Most Bluetooth devices can have multiple devices paired to it and some allow multiple devices to be connected and some only one to be connected. But even the ones that only allow one device to be connected allow multiple to be paired. So, if 1 and 2 are paired, then 2 can't connect while 1 is connected but it can connect as soon as 1 disconnects. If I am reading this correctly only one device can be paired. So for 2 to connect, 1 would have to disconnect and unpair and then 2 would have to pair and connect. Then for 1 to reconnect, 2 would have to disconnect and unpair, 1 would have to pair and then connect. Do I have this correct?

A: You've got it.

Q: 2. What is the range of this device?

A: I use this in a open gym and we get about 70 Feet no problem.

Q: 3. If I use 2 of these units for different rooms in the same building (funeral home with different viewing rooms) are they unique as far as ID?

A: No. But if you are concerned about them interfering with each other; Bluetooth signal cannot communicate through walls or floors.

Q: 4. Can the antenna be disconnected and attached to an extension cable to mount out side of rack enclosure ?

A: Hi, thanks for asking!No, the antenna is not detachable.

Q: 5. connecting R-S202 to Pioneer FS52 Floor standing speakers should I use regular wiring or bi-wiring? Which is one is better?

A: The Yamaha R-S202 Stereo Receiver with Bluetooth (Black), B&H # YARS202BL, should sound more or less identical regardless of whether it has standard wiring or bi-wiring. Bi-wiring can potentially reduce resistance within the wiring, but this difference would likely not be audible on any equipment being used outside of a professional studio, and therefore wouldn't make much of a difference on this particular receiver.

Q: 6. will this unit transmit audio to bluetooth speakers?

A: No it doesn't

Q: 7. Does it come with a power supply?

A: Sure does you just need audio cables.

Q: 8. This may sounds like an odd question, but are the feet removable? The only way this will fit in my cabinet is to remove the feet.

A: Yes you can remove the feet on the Yamaha R-S202.

Q: 9. what is the warranty?

A: This will come with a Limited 2-Year Warranty from the manufacturer.

Q: 10. Can I connect speakers to this ES202 then to my TV?

A: You mean R-S202 ? Please detail what you want. Are speakers not loud enough?

There are no reviews for this product.