Condenser Microphone Pair

Rdl Db-tps3a Triple Pair Rj45 Sender Module (black)

Product Code: ga174403
Availability: In Stock

$687.42 $989.88

Qty

12 reviews Write a review

Description
Reviews (12)

The DB-TPS3A Triple Pair RJ45 Sender Module from RDL is a three-pair audio sending module compatible with RDL Format-A twisted pair products. The DB-TPS3A features a black front-panel laminate. This module features an XLR microphone input and two RCA phono jack inputs, one for the left channel source and one for the right channel source. The unbalanced inputs are designed to receive standard -10 dBV consumer level signals. The microphone input provides 24 VDC IEC phantom voltage and accepts both dynamic and condenser microphone signals. The input signals are amplified using studio-quality pre-amplifiers optimized for normal operating levels. A rear-panel GAIN switch is provided to set the amplification of the microphone pre-amplifier. This switch is normally set by the installer for NORM (normal) gain. If consistently low microphone levels are expected, this switch may be set to the HIGH gain position. The pre-amplified microphone source is routed to pair A. The buffered left and right line-level inputs are routed to output cable pairs B and C.

The DB-TPS3A can be powered directly from a 24 VDC power supply using the rear-panel detachable terminal block. Local power connected to the module is also fed to all connected remote modules. The DB-TPS3A may be remotely powered through the twisted pair cable from any other module, signal distributor or RDL power inserter connected to the same twisted pair cable. Module power is indicated by a front-panel LED. This unit is designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources. The DB-TPS3A model can mount in RDL WB-1U and WB-2U wall boxes, or in standard U.S. electrical boxes.

Parameters
Inputs	Microphone: 1.2 kOhms balanced with IEC 24 VDC phantom Line (left and right): 10 kOhms unbalanced
Input Connections	XLR, microphone RCA phono, Line Format A Single Pair Used: A (Mic); B (Unbalanced Line Left); C (Unbalanced Line Right)
Input Level	Microphone: -45 to -65 dBu balanced; Maximum: -40 dBu (HIGH Gain), -28 dBu (NORM Gain) Line: -10 dBV unbalanced; +10 dBV Max
Output	RDL TP Format-A
Output Connections	RJ45
Frequency Response	Microphone: 100 Hz to 30 kHz (± 1 dB); integral low-cut filter -10 dB @ 30 Hz Line: 20 Hz to 50 kHz (± 0.5 dB)
THD & Noise	Microphone: < 0.1% (80 Hz to 20 kHz) Line: < 0.05% (20 Hz to 50 kHz); <0.005% (1 kHz)
Noise	Below +4 dBu Microphone: < -80 dB (Norm Gain), < -70 dB (High Gain) Line: < -95 dB
Crosstalk	Line to Line: < 90 dB (1 kHz); < 75 dB (20 Hz to 20 kHz) Line to Microphone (High Gain): < 65 dB (1 kHz), < 60 dB (20 Hz to 20 kHz) Line to Microphone (Norm Gain): < 75 dB (1 kHz), < 70 dB (20 Hz to 20 kHz)
Headroom	Above +4 dBu: > 18 dB
CMRR	Microphone: > 60 dB (HIGH Gain 50 Hz to 150 Hz), > 65 dB (NORM Gain 50 Hz to 150 Hz)
LED Indicator	Power In, blue
Power Connections	2 x RJ45; Detachable terminal block
Power Requirements	24 VDC @ 65 mA plus connected loads
Ambient Operating Environment	32 to 131°F (0 to 55°C)
Minimum Depth	Mounting Box Minimum Depth: 2.4" (6.1 cm)
Dimensions	1.6 x 4.11 x 1.89" (4.8 x 4.06 x 4.8 cm)
Weight	0.24 lb (0.11 kg)
Packaging Info
Package Weight	0.405 lb
Box Dimensions (LxWxH)	4.8 x 4.8 x 2.2"

Balanced microphone XLR input with phantom

Switch-selectable Mic Gain on rear panel

Two unbalanced -10 dBV phono jack line inputs

MIC feeds Pair A; L feeds Pair B; R feeds Pair C

Remote powering through twisted pair cable

Fused local power feeds all connected modules

Local power input on terminal block

Blue LED indicates module is powered

Utilizes all three Format-A pairs

Studio-Quality Precision Active Balanced Circuitry

Related Questions and Answers

Q: 1. What material is the black plating on the steel surfaces?

A: The Matthews Baby Junior Triple Riser Stand (Black, 12.25') BH #MABH386020 is painted.

Q: 2. Can a boom arm be safely added to this stand? If so, which is recommended?

A: Yes it can be used with a boom arm safely.

Q: 3. Would anyone know and or can confirm the size of the knob used to secure the this extension arm/tripe header? 3/8?

A: the size is 5/8"

Q: 4. What is the height in inches, or cm, from the top to the bottom shoe bracket? There only seems to be information on the width and not the height

A: The height of this Bracket is 8’’ from top to bottom.

Q: 5. Can you spin the flash head like the Joe McNally version of multiflash holders?

A: No, you cannot rotate the flashes at the base where it connects.

Q: 6. Will these fit the Sony MDR-V150 headphones?

A: Hi Jill, I’m quite sure they will fit. If for any reason they don’t, please email us at support@bluestarproducts.ca for help. Thanks for asking, Peter Bluestar Support Team - Canada

Q: 7. can i remove the wheels??

A: Not without permanently damaging the stand. But there is no need to do so as the wheels all have VERY stable locking mechanisms. Once you lock the wheels, the stand won't move. In fact, locking the wheels also locks the rotation of the caster, so it doesn't even shift from the connection of the caster to the leg. If you don't want wheels, you should get a C-stand instead.

Q: 8. Do the wheels on this stand lock?

A: Yes, the wheels lock. In fact, locking the wheels also locks the rotation of the caster, so it doesn't even shift from the connection of the caster to the leg.

Q: 9. What's the load capacity?

A: The Impact Baby Triple Header is made of steel, so it's especially strong. However, the manufacturer does not list a specific weight capacity. Balance likely would be more likely to be an issue than weight handling since typical C stands only take about 22 lbs. anyway.

Q: 10. I need a bracket that has one hot connection on it for my flash, the others can be cold. I'm guessing this won't work?

A: Unfortunately no. The Vello V-Rig 5" Triple Shoe Bracket is a cold shoe bracket only.

Hookster	08/09/2024
I have owned Bose speakers for over 14 years and once again I am very impressed, in fact I am going to be buying another immediately 5

Mannix511	16/08/2024
Very much satisfied with this speaker. Small but terrible in sound as if you’re listening to a big speaker! 5

RMRdz	08/08/2024
Bought the Bose speaker and I love it. The sound is awesome and the battery lasts for hours. 5

Sdlm39	28/07/2024
I have both this and and the Soundlink Color II. I've love them both, but the tone of this one is magnificent! 5

Vigor7474	16/07/2024
Awesome speaker. Great sound. Wish it was a little bit louder but so it's the best, clearest, and loudest speaker I have tried. 5

Norris	12/07/2024
Works like a charm. Great sound. Easy setup. 5

Warman23	01/06/2024
It's the best Bluetooth speaker ever used it has good bass 5

neo723	25/05/2024
I’ve been wanting to get this Bose Soundlink revolve II for the longest time. Everything I hope….awesome !I want to get another one…. So I 5

Nanu	21/05/2024
I got it for my birthday... So happy that I have it and it's like expensive sound system in my small room 5

Codyyodc	04/05/2024
I listen to my Bose speakers everyday in party mode it changed the feeling in the room in the best way. the second series is more impressive the my old two models 5