The white D-RLC10M Remote Level Control with Muting, Rotary from RDL is a rotary remote level control with pushbutton muting that provides you adjustment at single or multiple locations. Optical encoder technology allows continuous knob rotation with a comfortable adjustment rate and long-term trouble-free and noise-free operation. These controls directly connect to any RDL VCA and OEM equipment with 0 to 10 Vdc ramp inputs.

A single D-RLC10M may be connected to a ramp-controlled VCA using a single-pair shielded audio cable or unshielded cable. A rear-panel switch configures the control as the MASTER. The MASTER mode causes this control to drive the 0 to 10 Vdc ramp output and to monitor its pulse terminals in case any other -RLC10M controls are connected. As many as nine additional -RLC10M controls may be wired in parallel with the MASTER control using UTP cable (CAT5, CAT6 or equivalent). The rear-panel MODE switch on each additional remote control is set to SLAVE mode.

Operation is the same for a single control, or for each control connected in a multiple control point installation. The 0 to 10 Vdc ramp voltage is incremented up or down when the front-panel knob is rotated. Acceleration is provided so the rate of change is faster when the knob is rotated more rapidly, yielding a responsive feel and rapid elimination of acoustic feedback. The LED ring display encircling the control knob operates as a virtual pointer. When an -RLC10M is not being adjusted, its display switches to a dim intensity to avoid being a visual distraction. The display returns to a bright intensity during adjustment.

Upon power-up or re-powering after a power loss, the 0 to 10 Vdc ramp will output either a preset level or the last level used. The power-up mode is stored when the control is installed. When programmed for the preset level mode, the user can store a new preset level by holding the MUTE button for more than 3 seconds.

Multiple -RLC10M controls set to the SLAVE MODE may be connected to an RDL RU-VCA2A or RU-VCA6A, utilizing the VCA as the ramp generator. This connection is also possible with OEM equipment accepting open-collector pulses that are compatible with the -RLC10M output pulse rate and width.

Single or multiple control locations

Up to 10 remote control locations

Visual level display of operating level

Display is bright during adjustment and dims after adjustment

Steel frame construction

Electronics protected by rear enclosure

Detachable terminal block connections

Related Questions and Answers

Q: 1. I did not see EOS 10D, is this remote compatible?Do you have other Canon remote recommendations if not?

A: No, it is not compatible since the camera does not have an IR sensor built in. It uses a 3-pin connector like this Vello shutter release: https://bhpho.to/2dPByMI

Q: 2. Can this trigger multiple cameras at the same time? Is it compatible with 5D Mark IV?

A: The RC-6 remote control is compatible with the Canon 5D Mark IV but it cannot fire multiple cameras simultaneously because the remote must be aimed directly at the camera to trigger it.Enjoy,Paul

Q: 3. can the Canon RC-6 trigger work with the Canon R5?

A: Yes. This remote can be used with the Canon EOS R5.

Q: 4. I can't make it work with the EOS utility tool on my laptop in the live view mode with the studio flashes on... Can u help me please?

A: I was having the same issues...

Q: 5. Canon 6d mark 11 manual

A: Yes this would work with the Canon 6D Mark II while set in manual.

Q: 6. To use this with a Pentax 645z, do you have to point it at the back of the camera, or can you use it in front of the camera?

A: The remote is an infrared (IR) device. There is an IR sensor on both the front and the back of the camera, both of which blink a red light when you have set the camera to operate with the remote. Point the remote at the blinking red light.

Q: 7. Hi! What range could you reasonably expect this to work out to? I have the older remote that came with my Pentax K-5, and it only works out to about 10-15'.

A: Like the other Pentax infrared remotes, performance depends heavily on ambient light conditions. Outdoors in bright sunlight you should not expect more than 15 ft, depending on sun direction. Indoors or int dark conditions, 25-30 feet is reasonable.

Q: 8. will this work with canon rebel T100/EOS 300D?

A: No, this is not compatible with the 300D.

Q: 9. Is it compatible with a eos m10

A: Yes, this remote is compatible with the Canon EOS M10.

Q: 10. Does this work with 2 Canon 5DS R Mark III cameras? Yes, I have two cameras, do I need 2 of these, or one RC-6 wireless can control both of my cameras?

A: One will control both cameras as long as the sensors are in range.