Pair Samsung Level Headphones

Rdl D-tps8a Active Two-pair Sender With Format-a & Mini-jack Inputs (white)

Product Code: ga174609
Availability: In Stock

$588.00 $934.92

Qty

0 reviews Write a review

Description
Reviews (0)

The white D-TPS8A Active Two-Pair Sender from RDL is a two-pair audio sending module compatible with RDL Format-A twisted pair products. This module is designed to be mounted in wall boxes, cabinets, or other enclosures that allow users to connect audio sources. It features a white front-panel laminate with gray lettering that matches RDL Decora-style remote controls.

The D-TPS8A module features a stereo mini-jack input on the front panel. The input is designed to receive standard -10 dBV consumer-level signals from sources such as a computer or personal media player. The input signals are amplified using studio-quality preamplifiers optimized for normal operating levels. The buffered left and right inputs are routed to output cable pairs B and C.

This module drives only two cable pairs and therefore it accepts signals and power from one mic-level or line-level Format-A single-pair sender. One single-pair sender may be chained with the module. A single-pair sender must be set to feed pair A if it is connected together with the D-TPS8A Sender.

The D-TPS8A module has a Format-A input on the rear panel. This RJ45 input receives left and right signals from preceding senders and sums them together with the local mini-jack input. This allows multiple D-TPS8A modules to be connected in series with all the mini-jack inputs remaining active.

The D-TPS8A Sender is remotely powered through the twisted pair cable from any other module, signal distributor, or RDL power inserter connected to the same twisted pair cable. There are no illuminated indicators that could be distracting in dark locations, such as a hotel room. The unit features automatic fused power, hum rejection, low noise, and low distortion for designers and installers looking to work with twisted pair products.

Parameters
Inputs	Two 10 kΩ unbalanced, stereo; Format-A
Input Connections	Mini jack (front panel); RJ45 (rear panel)
Input Level	-10 dBV; +10 dBV maximum
Twisted Pair	Format-A Signal Pairs Used: 2, B (Left), C (Right)
Gain	12 dB
Output	RDL TP Format-A
Output Connection	RJ45
Frequency Response	20 Hz to 50 kHz (±0.5 dB)
THD + N	<0.1% (20 Hz to 50 kHz); <0.01% (1 kHz)
Noise	Below +4 dBu: <-85 dB <-75 dB with up to 10 TPS8A modules connected
Crosstalk	<85 dB (1 kHz); <75 dB (20 Hz to 20 kHz)
Headroom	Above +4 dBu: >20 dB
Power Connections	RJ45
Power Requirement	24 VDC @ 30 mA
Ambient Operating Temperature	32 to 131°F (0 to 55°C)
Dimensions	1.33 x 1.72 x 4.11" (3.37 x 4.36 x 10.43 cm)
Weight	0.39 lb (0.17 kg)
Packaging Info
Package Weight	0.415 lb
Box Dimensions (LxWxH)	4.9 x 4.1 x 2.3"

Unbalanced -10 dBV mini-jack audio input

Rear-panel RJ45 input for connecting additional TPS8A senders

Left (L) input feeds pair B; right (R) feeds pair C

Signal and power pair pass-through on RJ45 jacks

Remote powering through a twisted pair cable

Daisy-chain with single-pair senders

Studio-quality precision active balanced circuitry

Related Questions and Answers

Q: 1. What type of battery does it contain?

A: No batteries needed. Its a manual camera.

Q: 2. can these two channels be bridged?

A: to the best of my knowledge, no. Basic 2 channel amp, but it does what it is supposed to do well with low distortion and dependable output levels. I used it for wired speakers on my patio, Bose, that are not that efficient, but it drives them well and cleanly. Hope this helps.

Q: 3. The B&H spec says output is 1/8" TRS line-level unbalanced. However unbalanced is normally only 2 conductors (TS) not TRS right? Can anyone clarify the wiring of the output connector? Sennheiser's site and manual are useless in this regard.

A: Tip = hot Ring and Sleeve are shorted for sheild.

Q: 4. How much does the Kupo mini articulated one section arm (11.2") weigh? I see the package weight is 1lb but I would like to know the actual weight of the item. Thanks!

A: Product Weight: 0.90lb (0.41kg)

Q: 5. Does anyone know if this provides power to Lavs like the the Cos-11 that require power?

A: While I have not tried it with this particular Lav, Sennheiser did say that this systems wiring scheme is identical to the Sennheiser EW Evolution wireless and is compatible with all mics that are wired for the Evolution wireless.

Q: 6. How much weight can this support?

A: At least 4lb

Q: 7. What is the output ohms for the speakers?

A: its 4-8ohms

Q: 8. Can this work with Tascam 10L mic or any Pyle MEMS 10 over Ear Mic Headset

A: Yes, the Tentacle Sync Lockable 3.5mm Mini Jack for TRACK E can be used for a Tascam DR10L Microphone as well as any other microphone that requires a balanced cable.

Q: 9. I have an existing set of speakers going to my pool deck (Ch.2), and a set at the pool house (Ch.1). I'm looking to amplify the ones on the deck (Ch.2) so I have a balanced volume. Can I connect the existing speaker output (Ch.2) speaker to the input AUX. of this amplifier then run the speaker output from the amp to the pool deck and boost the volume?

A: Adjust the balance control.

Q: 10. Can the USB port be used for a Bluetooth USB adapter to stream audio?

A: No, the USB port on the Pyle Pro PTAU45 Mini Stereo Power Amplifier cannot be used to connect a Bluetooth USB adapter, however, you can use a Bluetooth adapter with a standard analog audio plug to connect to the RCA aux inputs or the 3.5mm CD/MP3 input. The Aluratek iStream DockFree Bluetooth Audio Receiver (B&H # ALAIS01F) could be a good option for a Bluetooth adapter. It has a 3.5mm plug and comes with an RCA adapter.

There are no reviews for this product.