The black iSeries 1510-6 Waterproof Utility Case with Layered Foam from SKB features a layered foam interior which can be cut to custom fit the items you are transporting. The injection-molded case is made of polypropylene copolymer resin and is waterproof, gasketed, dust-tight, and submersible (MIL-C-4150J). The case is also resistant to UV, solvents, corrosion, fungus, and impact damage. Molded-in hinges and trigger release latches add to the security of the case. A comfortable rubber overmolded cushion grip handle snaps into vertical/horizontal place for convenient carrying. A built-in automatic ambient pressure equalization valve (MIL-STD-648C) allows for safe air travel.

Waterproof / Gasket-Sealed    ATA 300 Rated    Impact-Resistant / Dust-Tight    UV and Solvent Resistant    Corrosion and Fungus Resistant    Molded-In Hinge    Pressure Equalization Valve    Snap down Cushioned Handle    Trigger Release Latch System    Stainless-Steel Locking Loops

Stainless-steel locking loops

Waterproof and dust-tight design

Molded-in hinge for added protection

Trigger release latch system

Snap-down rubber overmolded cushion grip handle

Ambient pressure equalization valve

Resistant to UV, solvents, corrosion, fungus

Resistant to impact damage

ATA 300 rated (Airline Transportation Association)

Accepts TSA (Transportation Security Administration) latches

Related Questions and Answers

Q: 1. where do you store the top handle?

A: Do you mean the handle for the shoulder rig? If so, I store in the wide space on the right of the case.

Q: 2. Will this work for the C100 Mk II?

A: It worked well with my C100 mkI so I'd say you'll be fine!

Q: 3. No dimensions listed. The only dimensions are for the box BH ships it in. What are the internal dimensions of this case?

A: The interior dimensions are L x W x D: 17 x 11.5 x 6.16" (43.18 x 29.21 x 15.65cm) with the foam removed.

Q: 4. Would this case hold a G50, being that the G50 is basically a XA40 without the handle?

A: The Canon G50 will fit in this case, however, it will not be as effective at protecting the camera. The excess space (for the top handle) gives the camera room to move around inside the case. If you plan to use this for keeping your camcorder organized then this case will work very well. All of the accessories are the same for both camcorders (except audio).

Q: 5. Will this case hold a Canon 70-200 2.8 IS II lens standing up (vertical), or does it have to lay down (horizontal)?

A: The lens is about 8" long and the dimensions of the case are 20.4 x 11.4 x 7.5", so the lens will fit in two of the dimensions, but not in the third, shortest, dimension.

Q: 6. will this fit the XA70?

A: Yes, the SKB iSeries Case for Canon XA11/15/40/45/60/65 & Accessories will accommodate the Canon XA70 UHD 4K30 Camcorder with Dual-Pixel Autofocus (B&H # CAXA70).

Q: 7. What's the depth from foam base to the foam top? What is the interior width & length with the ThinkTank outer padding?

A: The SKB iSeries 1510-6 Case with Think Tank Photo Dividers & Lid Foam has a 1.75" / 4.45 cm (Lid Depth) and 4.25" / 10.79 cm (Base Depth).

Q: 8. Could you fit a 1dx mark iii or canon c200 in this case?

A: Yes, you can.

Q: 9. Will this case fit a sony 200-600mm lens with sony a7riii body attached?

A: The inner dimension of the case is 15 inches. The Sony 200-600mm and Sony A7RIII is 15.42 inches. You will be able to fit the lens and camera body if you detach the two items.

Q: 10. Will this fit a C300 mark II ?

A: It's a very tight fit. Not much extra room