The black Winsted E-SOC Control Station with Articulating Monitor Mounts is a workstation that comes with three articulating monitor mounts and features the Versa-Trak monitor mounting system for ergonomic comfort and adjustability. Lift-off access panels, integrated cable management, and a hinged corner make this station a flexible solution suitable for control room applications.

Decorative, vented modesty panel features convenient lift-off panels for easy access to cables, electronics, and CPUs. Integrated cable management with lacing loops keeps cables out of the way.

Hinged corner offers flexibility with no pre-defined corner angles.

Integrated horizontal aluminum track system will support a wide variety of monitor arrays. Versa-Trak offers versatility with easy horizontal adjustment. Post-mounted VESA brackets provide vertical adjustability along with the ability to tilt and pivot the monitors.

Coated with a durable black powder-coat paint that accentuates the work surface. Textured finish prevents fingerprints and lasts for years.

Features a cable channel with lacing hoops incorporated into the modesty panel and a large, drop-down hinged cable tray that spans the length of the modesty panel.

VESA-compliant pivot/tilt mounts easily attach monitors to a support post, and provides smooth pivot and pitch adjustment for optimal viewing of flat panel monitors.

Related Questions and Answers

Q: 1. Are these with 6mm or 8mm couplings, or neither?

A: The Vixen Optics Slow Motion Control Knob for AP, GP2, and GPD2 Mounts is a replacement knob for those mounts. The knobs mount on a shaft that is roughly 6mm in diameter.

Q: 2. Will the clamp fit through a 2.5 inch hole? My cubicle backs up to a wall, i'd have to insert the clamp into the extra cable hole in the desk.

A: It depends on the exact shape and depth of the hole. The mounting flange is just shy of 2.5 but is D shaped (to go along a wall). The flange may or may not fit into the hole as the longest distance from the corner of the D to the opposite rounded edge is closer to 3 . However the clamping depth/height may allow for the rounded portion to fit to the hole and allow you to bring the entire clamp forward so that the rear-flat part of the D can take up the diameter of the hole. If the hole is only 2.5 and the desk thickness is more than 1.5 you might not be able to fit the clamp.But if the desk is about 1.5 and the hole is a generous 2.5 you will probably be fine.

Q: 3. Can you set the monitors side by side at different heights? (i.e., I have 2 different sizes of monitors and I like them set so the top edges line up, not the centers...)

A: Monitor heights cannot be independently adjusted.

Q: 4. Do these knobs come with 6mm or 8mm couplings, or neither?

A: The knobs are the same size that came with the Vixen AP, GP2, and GPD2 Mounts originally.

Q: 5. Could I run a stereo signal into this box & send that same stereo out, but allow headphone monitoring of the signal?

A: Yes, this box has a 1/4-inch input that can be switched to stereo, and has a left and right XLR line level outputs, as well as a headphone jack.

Q: 6. From the center of the monitor, what is the max height?

A: I would say 18 to the center of the monitor is the max height.

Q: 7. I'm new to this kind of stuff but have 2 LED displays. Does it matter if I have LED or LCD displays for this mount to be compatible?

A: Makes no difference. the bracket does not discriminate. What does matter is whether your monitors have a 3 or 4 hole pattern for mounting, but these two hole patterns are typical to just about all monitors.

Q: 8. This Monitor mount works with iMac 21"?

A: The 21.5" iMacs can't be mounted.

Q: 9. If I were to use this in line with the MX41 as an input to increase inputs to the monitor, would the signal from the mx41b come through ?

A: To begin with, I'm confused with your question, as you refer to an MX41, and an mx41b. Presuming that you mean the Rolls MX41B in both instances, then I am further confused by your question about whether the signal from it would come through. The more clearly you state your question, the better the rest of us can understand and offer help.That being said, there should be no problem to take the output from the MX41B into either the line input or instrument input of the Rolls PM351 and hear all the inputs from both units mixed together on the output of the PM351. It has lots of range and volume available, and is a great, clean headphone amp/mixer/direct box. You will want to pay attention to your stereo and mono cables, as well as the stereo/mono jumpers on the PM351, so you know what you are actually listening to. The MX41B is stereo, so I don't know what happens when you put a mono cable into it... it may only appear on one side of the output. Stereo/mono on the PM351 is selectable with two jumpers. Careful with those jumpers, though, they are black and small and easily lost.The quarter-inches are all unbalanced, too, so don't run those cables more than about 10 feet if you can help it. The XLR's are fine for any length, of course.Hope that helps.rcarbaugh

Q: 10. I have two 27in monitors will are the arms long enough to have both side by side?

A: You should no have issues mounting two 27" monitors with this mount.