The blue Canare L-5CFW RG6 BNC Male to Right Angle BNC Male HD-SDI Video Cable is a 1' cable that is hand-assembled with Canare extra flexible L-5CFW HD-SDI RG6 coaxial cable, and Canare true 75-ohm HD BNC connectors. This cable is 100% sweep tested to conform to SMPTE 259M, 292M, 424M, 2081-1, and 2082-1 standards. The combination of Canare BNC connectors used in this series exceed 3.0Gb/s HD-SDI requirements specified in SMPTE 424M and are fully rated for extended distances for 3G-SDI ST424 out to 340 Feet.

18 AWG RG6 SDI Coaxial Cable    BNC Male to Right Angle Male Connectors    Solid Copper Center Conductor    Foam PE Dielectric Insulation    Dual Copper Braid    100% Sweep Tested

Hand made with Canare L-5CFW 18AWG stranded center conductor, 75-ohm Precision HD-Serial Digital Video Coax cable for professional broadcast performance

Cables meet SMPTE 259M, 292M,3G 3G 424M, 6G 2081-1, 12G 2082-1 Standards

Canare BCP-B51F straight, and BCP-LC5F right angle, true 75-Ohm BNC connectors, exceed 6.0Gbps HD-SDI SMPTE requirements

Dual copper braid for flexibility and bending performance

100% sweep tested

Related Questions and Answers

Q: 1. Can the receiver output HDMI and SDI at the same time to enable a loop to another monitor?

A: Yes you can. If using a smallhd monitor you can just run one sdi out to that, and loop out of the smallhd as well.

Q: 2. One of the pictures shows a non right-angle usb-c connection. Is that a mistake, and if so, does this cable also come in a straight usb-c connector version?

A: Correct as shown and described. See the third image down on the left hand side. Th first image is not correct for this item and is actually for this cable: IndiPRO Tools 2.5mm DC Barrel to Mini USB 5 VDC Power Regulated Cable (24") B&H # IN39PPC

Q: 3. Will this Zacuto cable for the ZSG-C10 Zoom Grip allow control of the start stop on the Sony FS7?

A: Unfortunately not. This cable has no where to go on the Sony FS7. You can mount the lens with a smart EF to E mount adapter and power the zoom. But sorry, no record start and stop.

Q: 4. I can't connect it to ghost eye 150mV2, either receiver or transmitter. Any solution?It state that it is compatible to the previous version.

A: We are sorry to hear about any issues you are facing with this product. So that we may best assist you feel free to email us directly at askbh@bhphoto.com.

Q: 5. Does it work with Hero 8?

A: Yes this unit in compatible with the GoPro HERO 8

Q: 6. Can this device pass full Ancillary Data? Particularly SDI Audio Channels 15&16, the channels used for Blackmagic's CCU data. I know some of these units either compress or strip down the audio channels if they're based on WHDMI chipsets.

A: I dont believe it passes the full ancillary data, not 100% on this. Worked on a set where they requested teradeks for this exact reason.

Q: 7. Would this work with the Sound Devices MixPre-3 II audio recorder?

A: This is regulated to work with select GoPro cameras. We are not aware of it being able to work with a Sound Device Audio Recorder.

Q: 8. Is this compatible with the Cinegears 150m Receiver?

A: No this is Not compatible with the Cinegears 150m Receiver

Q: 9. Which end connects to the camera, the transmitter or receiver?

A: With systems like this you Transmit the signal from the camera to a monitor that has a receiver on it. The Transmitter will go with the camera.

Q: 10. How noisy is the transmitter?

A: The noise produced by the CINEGEARS Ghost-Eye 600MP Wireless Transmitter is very low, if barely audible on a microphone.