Providing you with the ability to adjust the friction drag of zoom lenses, the Manual Friction Adjustable Zoom Controller 0.6 Mod from LanParte mounts to your 15mm support rod and engages with your lenses compatible zoom gear. The built in friction drag adjustment allows you to increase the drag on a zoom lens, which can be helpful when making long, slow, smooth zooms. You can also dial the friction to off, freeing the lens from any additional drag from the unit. This controller is completely manual and features a zoom lever that you can attach to the controller at three different positions.

This unit is designed for lenses that feature a zoom gear with a 0.6 Mod such as Fujinon lenses.

Manual Zoom Controller    Mounts to a Single 15mm Rod    Adjustable Zoom Drag    3 x Positions for the Zoom Lever    For Lenses with 0.6 Mod

This is a zoom controller that allows you to add variable drag to your compatible zoom lens.

Related Questions and Answers

Q: 1. Will this transmitter fire the YN600EX-RT II and the YN685 flashes?

A: The Yongnuo YN560-TX II Manual Flash Controller for Canon Cameras would be compatible for use with the Yongnuo YN685 Wireless TTL Speedlite for Canon Cameras. The Yongnuo YN560-TX II Manual Flash Controller for Canon Cameras is not compatible for use with the Yongnuo Speedlite YN600EX-RT II for Canon Cameras.

Q: 2. Work with lumix camera ?

A: Unfortunately, this transmitter has not been tested to our knowledge with a Panasonic Lumix mirrorless camera. Your results may vary.

Q: 3. Is this compatible with a Blackmagic Design Video Assist 3G 7"?

A: Yes, the Blackmagic Video Assist 3G 7" has a LANC port that will accept the LanParte LANC Wireless Controller.

Q: 4. Besides the quick-lock on the hot shoe, is there any other difference with the original model?

A: The two units are basically similar. Besides the new quick locking hot shoe clamp, the YN560-TX II has a smaller and lighter body design compared to the original YN560-TX transmitter. Other slight differences would be a slightly rearranged LCD screen and a casing that allows you to load batteries from the front of the unit rather than from the side. The button layout would be identical. If you do not currently have a Yongnuo YN560-TX transmitter, then I would recommend the new YN560-TX II mainly for the better locking shoe design. However, if you already own the original YN560-TX and it is working properly, there is no big reason to upgrade to the newer transmitter.

Q: 5. Can it be used on Nikon cameras?

A: Yes, the Yongnuo YN560-TX II Manual Flash Controller for Canon Cameras would be compatible for use on Nikon cameras. However, do note that this transmitter will not have the flash wake-up feature to awaken off-camera Yongnuo flashes as the hot shoe pin setup for communication on the Nikon hot shoe differs from the pin alignment of the Canon transmitter. However, as the main central SYNC pin is the same on all standard ISO hot shoes, the Yongnuo YN560-TX II Manual Flash Controller for Canon Cameras may be used with any camera that has a standard ISO hot shoe, but will only wake up off-camera wireless flashes when connected to a Canon EOS camera.

Q: 6. will this work for yongnuo yn968n speedlites?

A: No it will not work at all.

Q: 7. What type of batterys does it use?

A: Using the 2.5mm LANC cable to connect the receiver to the camera body, the receiver can draw power from the camera directly. The transmitter uses a replaceable button cell.

Q: 8. does the transmitter have a LANC socket on it so I can plug in a zoom controller? I want to leave it on my tripod handle.

A: The LanParte LANC Wireless Controller (Start/Stop) Kit does not have an additional input to allow connection of additional controllers.

Q: 9. Will it work with a yongnuo yn600ex-et?

A: not work, buy radio reception extra RF-603C II for flash (recept RF-603 work for transmitter YN560-TXII). the transmitter YN560-TXII work direct flash YN560-III, YN560-IV, YN660, YN685, YN968.

Q: 10. Is this just the LANC-01 with an added wireless remote?

A: No it is not.