Giving you 2 passive channels for stereo or dual mono DI applications, the JDI Stereo Passive Direct Box from Radial Engineering features Jensen transformers that balance your signal and lower its impedance for driving long cables. The unit boasts a flat frequency response from 10 Hz to 40 kHz, allowing the natural sound of your instrument to be unchanged. Each channel has a -15 dB selectable pad, along with transformer-isolated inputs and outputs, to help reduce noise. Interference is further reduced thanks to its internal Faraday shield. The JDI Stereo's 14-gauge steel construction allows the box to be just as suited for the stage as the studio.

Equipped with Jensen Transformers    -15 dB Pad Per Channel    Flat Frequency Response    Transformer-Isolated I/O    14-Gauge Steel Construction    Internal Faraday Shield

Jensen transformer-equipped passive DI

Eliminates hum and buzz from ground loops

Virtually zero phase & harmonic distortion

Compact stereo format

Related Questions and Answers

Q: 1. will this work with bolt6 LT 750?

A: Yes, the Teradek Dual Direct Mount Battery Plate for L-Series and LP-E6 Batteries will work with the Bolt LT750. It is compatible with: Bolt 1000/3000 XT Transmitters Bolt 500 XT Transmitters and Receivers Bolt XT Sidekick All Non-4K Bolt LT Models Please Note: This battery plate will not work on Bolt 1000/3000 XT Receivers.

Q: 2. Will this work on the Teradek 4k bolt 750 LT transmitter?

A: No.

Q: 3. I have a landline with a chord, but I use a wireless headset quite often. Will this device pitch up recordings of conversations on my wireless headset?

A: The connector will only work while you're using the wired phone headset.

Q: 4. We just ordered the new 2020 iMac 27' with a stand. Is there an adapter that will work for it?

A: No. This would only be compatible with the following iMac computers iMac (27-inch, Mid 2011) iMac (27-inch, Mid 2010) iMac (21.5-inch, Late 2009) iMac (27-inch, Late 2009) iMac (20-inch, Early 2009) iMac (24-inch, Early 2009) LED Cinema Display (24-inch) LED Cinema Display (27-inch) Apple Thunderbolt Display (27-inch) For the 2020 iMac 27" This is the correct part number and link BH #TEVADPT07 • MFR #VADPT07 https://bhpho.to/3lamI6K

Q: 5. Once I connect the JST connectors, where am I supposed to tuck them into? The gap inside the battery plate, or the gap inside the Bolt 500XT transmitter?

A: As other users have defined, you can press the cable from the transmitter into the gap and align the connector to allow the battery plate to press into the opening. It's going to be a tight fit, but it should work.

Q: 6. Is the connector that plugs in to the handset compatible with a 4 wire smaller male end?

A: Yes this unit connects to the RJ11 plug between the handset and phone.

Q: 7. Will this fit on the 2019 model?

A: This item is not compatible with the 2019 model.

Q: 8. Can I hook it up directly to FIOS box?

A: If you FIOS box has a standard phone jack on it I would think it would work. I do not have a FIOS box so I can't say for 100%

Q: 9. How long will an L-series vs the LP-E6 battery run on a Teradek Bolt 500 XT transmitter? Thx.

A: This will depend on the exact NP-F style battery you use. However a large NP-F style battery, such as an NP-F975, is around 4-5 times longer in capacity than an LP-E6.

Q: 10. Hi, Is this compatible with Polycom Soundpoint IP 335 deskphones?

A: Check to see what sort of plug is on the end of the handset cord. This device works with phones that have a corded handset with a phone-jack-type plug that plugs into the phone - this device plugs into the phone and the handset cord plugs into the device. Then you plug the 3.5 mm audio connector into your recorder's microphone jack.