The Acebil CS-280G Professional Tripod System features a 75mm CH2 Fluid Head, T750 Aluminum Tripod, GS-3 Ground Spreader, and a S-50 Carry Case. The head supports loads up to 13.2 pounds and has a 6-step counterbalance and indepedent 4-step pan and tilt drag. It comes equipped with a sliding quick-release plate and pan handle.

The 1-stage T750 tripod features a 75mm bowl and can be adjusted to provide a height ranging from 26.4 to 56.7". Enhanced tripod stability is provided via the GS-3 Ground Spreader that holds the legs in position. A carrying case is included for easy storage and transport of the tripod system.

Supports Loads Up to 13.2 lb    CH2 Fluid Head    1-Stage T750 Aluminum Tripod    75mm Ball/Bowl    6-Step Counterbalance    4-Step Pan & Tilt Drag    Height Range: 26.4 to 56.7"    GS-3 Ground Spreader    S-50 Carry Case

• Supports up to 13.2 lb
• 75mm CH2 Fluid Head
• 6-Step counterbalance
• 4-Step pan/tilt drag
• 1-Stage T750 aluminum tripod with 75mm bowl
• Tripod height range: 26.4 to 56.7"
• GS-3 Ground Spreader enhances tripod stability and holds the tripod legs in position
• S-50 Carry Case included for storing and transporting the tripod system

Related Questions and Answers

Q: 1. is there another spreader I could use with this tripod to go lower, other than the one included?

A: There is a floor spreader model as well as this mid-level one seen here. Acebil T1002G Tripod Legs (100mm Bowl) B&H # ACT1002G. However, to get as low as possible with this tripod, you would have to remove whatever spreader it has. The lowest possible set up would come with a smaller tripod or a hi-hat. E-Image Hi-Hat with 75/100mm Bowl B&H # EI7500 is one possibility.

Q: 2. Can I use this with the iFootage Wild Bull T5S with the spiked feet (rubber feet removed)?

A: Yes, the Acebil D3 Dolly for Professional Tripods is compatible with the iFootage Wild Bull T Series T5S Aluminum Alloy Tripod.

Q: 3. Is the min height 17" or 25"? The aluminum version states both yet the Carbon somehow states its 17"

A: This tripod, Acebil T1002CM, has a height adjustment between 17.7 to 60.2''. The Aluminum Version, B&H # ACT1002G, is also 17.7 to 60.2". The model with a Height Range of 26.4 to 56.7" is a different tripod, it is the single stage B&H # ACT1000G.

Q: 4. Will it work with this tripod FEISOL CT-3441T ?

A: One would need to attach Feisol short spikes to make the tripod usable with the dolly: https://bhpho.to/2FQufIF

Q: 5. what is the minimum working height?

A: They do not list the minimum working height, but the center column can turn 90 degrees and the legs can open to a very wide angle so you can get very close to the ground. I would say around 4-5 inches from the ground.

Q: 6. Is this head compatible with manfrotto 501 quick-release plates?

A: Unfortunately, the Acebil I-605DX is not compatible with the Manfrotto 501pl plate.

Q: 7. Min height is 25" or 17"? It says both. Then again for some reason the Carbon version says its 17" too.

A: The height range of this tripod is 25.2 to 58.3 inches.

Q: 8. What is the size of the half-ball do I need to purchased for this type of tripod?

A: This is a 100mm bowl tripod. You would need to purchase a half ball like the Benro 100HB 100mm Half Ball Adapter, BH #BEBL100. https://bhpho.to/2kVsdwi

Q: 9. What is the screw size for mounting the camera or head to the Acebil MP-285C?

A: This monopod has a reversible stud that provides a 1/4-20 or 3/8"thread.

Q: 10. Can this dolly be used on a tripod without spiked feet?

A: The Acebil D3 is only compatible with spiked feet tripods.