The IR919 Series Long Range IR Illuminator from Iluminar emits infrared illumination, which is invisible to the human eye but can be seen by a night vision camera with its IR cut filter removed. The illuminator has a 10° light distribution angle that provides an HOV of 79’ and a range of 443’.

The IR919 illuminator is designed to provide IR lighting for CCTV systems. With an IP67 rating, the illuminator is weatherproof and can be used outdoors. The hardened housing provides protection from harsh weather conditions and rapid temperature variations (-58 to 140°F). This covert camera is not effected by light pollution and has a longer range (443’) than visible light illuminators due to its higher wavelength.

Long range IR illuminator

SMT LED technology

Range of 443'

10° light distribution angle

940nm wavelength

Covert illuminator with no visible glow from illuminator, making it ideal for transportation or high-security applications

Low power consumption (52W)

Long life

IP67 weatherproof rating

Built-in photocell IR on/off

Telemetry input for remote switching

24 VAC input

Related Questions and Answers

Q: 1. Can the center column be inverted to mount the camera under the tripod?

A: Yes, the center column on this tripod can be inverted to mount the camera below.

Q: 2. Is 70.5" the maximum height with the center column extended?

A: Yes it is 70.5 inches with the column or 58.9 inches without.

Q: 3. Is this tripod sturdy enough for a Nikon 600/4 VR mounted on a full Wimberley (WH-200)?

A: I have this tripod with the Wimberley gimbal head. Together they weigh about 7 pounds. I use this rig with a 200-400 and a 1.4TC and my D810 or D750. I get better results with the D750 as there is less sensitivity to micro-blur.The rig is substantial enough for my lens, but I do not know how much heavier/longer your 600mm lens is. I do not think weight is the issue, but you can check the specs and compare.My experience is that it is about technique and settings. I get best results with a bean bag resting on the lens, and if the target is stationary, I use m-up. Also use electronic front curtain shutter. The issue is vibration from the shutter rolling down the lens. I do not think this is a tripod issue. I sometimes use my arm laying on the lens if I am shooting fast enough.

Q: 4. Is there a ballast hook on both the long and short center columns? Or can the hook be transferred between center columns?

A: The default center column of the Benro TMA37AL has a ballast hook on it, however, the short center column does not.

Q: 5. Where is the serial number located on this item?

A: very hard to see-use a flashlight-Benro said the following-Blue numbers, across bottom of the label below the box with Mach 3 Number may be upside down-they sent me pictures which I can forward if you send me your email. the numbers are outside the box frame but on the label and are perpendicular to writing on the label Good Luck

Q: 6. Do the legs go out so the tripod is flat to the ground?

A: The Benro TMA38CL Long Series 3 Mach3 Carbon Fiber Tripod can go as low at 14 inches. It cannot go flat to the ground.

Q: 7. Can this AP be powered by a non-Ubiquiti PoE router such as Netgear GS108PE or TP Link SG1008PE?

A: It comes with a PoE injector, but it can be powered by PoE compatible routers as well.

Q: 8. What is the max height of the tripod without extending the center column? Thanks.

A: This tripod measures 59 1/2 inches without extending the center column and without a ball head mounted onto it. I am 6 ft tall, and I find this tripod to be more than adequate for all the landscape photography work that I do - note that it also comes with a short center column, allowing you to work very close to the ground if desired.

Q: 9. Can you attach an gimble head to this tripod?

A: As the Benro TMA37AL Long Series 3 Mach3 Aluminum Tripod has a 3/8"-16 male tripod thread on the top of the center column, yes, you may connect a gimbal that has a 3/8"-16 female threaded socket on the base of the gimbal head onto this tripod.

Q: 10. Does the Gitzo Center Column Bubble Level GLEVEL1 or GLEVEL2 fit on this tripod, too? I can't find any specific bubble level for series 3.Thank you, Philip

A: No, sorry neither will fit on a 3 series gitzo. If you need a bubble level, I would recommend one that attaches to the hotshoe of your camera.