Expand the connectivity options of your computer with the USB 3.0 Type-C Multi-Adapter Hub from j5create. This hub uses the USB 3.0 Type-C port on your notebook or desktop to provide the system with two USB 3.0 SuperSpeed ports as well as a Gigabit Ethernet jack and HDMI port. It allows you to quickly add wired networking, an HDMI-capable monitor, and two USB devices, such as printers and storage drives, to your computer. In addition, the integrated USB Type-C cable can charge your system with the help of an optional USB-C charger.

2 x USB 3.0 Type-A Ports    HDMI Port    UHD 4K Resolution    Gigabit Ethernet Port    Integrated USB 3.0 Type-C Cable

2 x USB 3.0 ports

Transfer rates of up to 5 Gb/s

Backwards compatible with USB 2.0 and USB 1.1 devices

Hot-swapping connect/disconnect without powering down

Related Questions and Answers

Q: 1. Does it support RAID 0 (disk striping) with 2 2TB SSDs?

A: Yes, this would work with RAID 0

Q: 2. Do the drives go entirely inside of the enclosure or do they stick out like a drive dock?

A: They stick out a little.

Q: 3. Can I use this MIDI hub in a live show? And would each MIDI controller work individually in Ableton Live (using different VSTs on each MIDI controller of course)?

A: Yes, the ESI M4U eX could be used for a live performance. Each MIDI input will be recognized as a separate channel by your DAW.

Q: 4. Would this work with SDXC cards? One photo shows an SDXC (with an upside down sticker), the specs say "unspecified".

A: Yes, the Sabrent 2-Port USB 3.1 Gen 1 Hub with HDMI Port, Power Delivery, and Card Readers is compatible with SDXC cards.

Q: 5. Hi - using this device, are drives hot swappable if not in raid mode?

A: Yes, see pg. 13 of manual: https://www.bhphotovideo.com/lit_files/640718.pdf

Q: 6. Does this require wall power or is it bus powered? The photos and description are confusing.

A: The LaCie 8TB Rugged RAID Shuttle USB 3.1 Gen 2 External Hard Drive B&H # LASTHT800080 works over bus power if you use it the USB Type C to Type C cable on a laptop with a native USB Type C port. If used with the included Type C to Type A USB cable and an older computer, you will need to use the included power supply.

Q: 7. Is there a fan in the unit? Also is it usb 3.1 Gen 1 (5 gb/s) or usb 3.1 Gen 2 (10 gb/s)?

A: As the title says:CineRAID CR-H218 2-Bay USB 3.1 Gen 2 ...CineRAID CR-H218 2-Bay USB 3.1 Gen TWO ...it is FAST, but not faster that what it is connected to is capable of taking.I get 700-800 on a stock Best of class MBPro and 910+ on an over clocked refrigerant cooled tower with a 12 core both doing contiguous transfers with a clocked bus and higher with TB3 1/2Meter cable and extreme clocking, you're mileage may vary.

Q: 8. This is Nguyen from MA and question for How to configure this overhub to define which port it should be connected to what? Is there the software comes with this device to config the port selection?

A: This hub is specifically designed to work with Overbridge enabled devices from Elektron, which will correctly route the connected devices.

Q: 9. My laptop only has usb type C, it does not have thunderbolt, this device can be used to connect it to my laptop convert the port into a thunderbolt to connect eGPU?

A: No the computer must have Thunderbolt 3. And if the computer has Thunderbolt 3 this is not used as a chassis for an eGPU but rather port expansion.

Q: 10. where can I get the power adapter for the CineRAID CR-H218? Tech support from CineRAID is non-reponsive on this...?

A: A Universal power adapter can be used such as the following: https://www.bhphotovideo.com/c/product/1117531-REG/cyberpower_cpuac1u1300_1300mah_universal_power_adapter.html