The black HD-150 Loaded Gear Hard Case from Barska is a waterproof transport case with a reinforced hinge, carrying handle, and latching closure. This configuration of the Loaded Gear case has a 0.42 ft³ capacity that is well-sized for a GoPro camera, sport optics, smart phone. Complementing the crushproof construction is an o-ring seal and built-in pressure equalization valve that equip the HD-150 for waterproof performance. The HD-150 includes egg crate foam padding on the top and bottom of the case's interior, and a pick-and-pluck foam sheet that enables the user to shape the padding to fit their gear. An extreme temperature tolerance and padlock port help make the HD-150 a full-featured hard case for reliable transportation and storage.

Crushproof Plastic Housing    0.42 ft³ Interior Volume    Pressure Equalizing Valve    Airtight O-Ring Sealed Interior    Two Flip-Lock Latches    Egg Crate Foam Top / Bottom Liner    Perforated Foam Padding

Pressure relief valve equalizes the case's interior and exterior atmospheric pressure

Egg crate padded top and bottom with additional pick-and-pluck foam padding

Airtight o-ring seal provides a waterproof interior

Reinforced flip-lock latch with padlock mounting port; two tie-down holes

Related Questions and Answers

Q: 1. are the locks currently TSA friendly?

A: The locks are not TSA friendly. However, there are 2 holes for locks in the lid. If you need to lock it, put your own TSA locks on there and leave the built in locks unlocked.

Q: 2. Does this case come from B&H with the casters included? There seem to be varied answers even though the vast majority says yes.

A: The Pelican 0340 Cube Case with Foam (Black) includes the casters built into it the case.

Q: 3. Would this make a good case for c-stands?

A: Yes, as long as they are turtle stands with removable legs.

Q: 4. Could I fit three standard tripods in this?

A: The Pelican iM3100 Storm Case has interior dimensions of 36.5 x 14 x 6 inches. It is possible to fit 3 tripods depending on the size.

Q: 5. Can we put in this case a Canon 6D and a Canon 70-200mm f/2.8 IS (mounted)? Thanks!

A: I Have a 5D and it doest fit the case with the lens mounted.

Q: 6. Will this case fit a Swarovski STS-65 scope with the eyepiece?

A: I'm using my case for Kowa 82sv angle head spotting scope

Q: 7. Will a Rebel T7 fit in this?

A: Yes, the Canon Rebel T7 will fit in the USA GEAR Quick Access DSLR Hard Shell Camera/Zoom Lens Case (Black).

Q: 8. Will it fit with Manfrotto MT055XPRO3 Aluminum Tripod+ Manfrotto 502HD Pro Video Head ?

A: I use mine to store 6 Impact Light Stands and 2 lateral balance arms. 3 of them are LS-96HAB (Large) and 3 are LS-10AB (small) with room to spare. I own a Manfrotto Tripod 3236 with a 3039 still camera head and it would fit in the case with lots of room to spare. I measured all the light stands when bundled up to consider what case I needed - so the specs provided by B&H were accurate. So if you measure your gear and compare to the specs that should be your best judgement for making your final conclusion. I will tell you this - it is a very sturdy case and the wheel casters work very nice over all kinds of surfaces. the pull handle is very sturdy as well. I have been very pleased with this purchase. Sometimes I have to set up a remote studio for some clients and getting my lighting gear to their locations needs to happen as quickly as possible. So if this ends up being the right size for your gear - I can assure you - you will be pleased with how well made and rugged this case proves to be. Hope this was helpful - best of luck - Dan

Q: 9. How deep with the case without the lid (just the bottom)?

A: The bottom is 4.5".

Q: 10. Would this case fit a Canon 7D Mk2 with a Canon 300/4L IS and 1.4 extender attached?

A: I don't think it would be wide enough with the body attached to the lens. It's quite narrow. I use just for a lens and scope. U have to leave a little room for the foam. My 1D does not fit width wise