Protect a variety of electrical equipment including computers, phones, fax machines, modems, and consumer electronics from harm due to electrical spikes with the CSP708T 7-Outlet Professional Surge Protector from CyberPower. It features 1650 joules of surge protection along with data line protection through the integrated RJ11 phone jack.

The CSP708T also supports data line protection, comes in an impact-resistant casing, supports metal oxide varistor (MOV) technology, and comes with an EMI/RFI noise filter. The CSP708T 7-Outlet Professional Surge Protector is covered by a limited lifetime warranty, while the included Connected Equipment Guarantee covers connected equipment up to $175,000.

Seven Surge-Protected Outlets    One Widely Spaced Outlet    1650 Joules of Surge Protection    DSL/Phone/ Fax RJ11 Protection    15A Circuit Breaker    8' Power Cord    EMI/RFI Noise Filters    Cable Management

Diverts excess voltage away from sensitive electronic equipment during an AC power surge or power spike to prevent damage.

Protects connected electronics with the integrated circuit breaker, which automatically switches off in the event of an overload exceeding the model's ability to suppress the signal.

RJ11 ports (1 in / 2 out) provide surge protection for telecommunications devices such as phones and DSL modems.

Maintains clean power for connected equipment by filtering out electromagnetic and radio frequency interference to improve picture and sound quality.

Allows normal current to pass through the device, while diverting any surges/spikes through the ground circuit, to safeguard connected electronics and the surge suppressor.

Light to indicate the model's status: Protected and Grounded.

Widely spaced outlet accommodates transformer-based plugs without compromising the access of other outlets.

Keeps cords neat and organized.

Enable the model to be placed on a wall, under a desk, and in other configurations to optimize space and keep power cords out of the way.

Ensures maximum durability and prolongs the life of the model.

CyberPower will repair or replace properly connected equipment if damaged by a power surge.

Covers defects in materials and workmanship in the product under normal use and conditions.

Related Questions and Answers

Q: 1. It looks like the protector case would interfere with the optional thumb support. Is this correct?

A: Not correct. You can use the protector with the thumb support. It will not interfere with the protector as it was designed to use it mind.

Q: 2. What is the run time at 50% load?

A: Run time at half load is about 9 minutes.

Q: 3. What are the benefits of having a UPS with pure sine wave as opposed to a UPS with a stepped approximation to sine wave?

A: For most devices simulated sine wave is adequate. However, if you are backing up a device with an Active PFC (power factor correction) supply they require pure sine wave to operate correctly. Active PFC supplies are considerably more efficient than standard power supplies but need a clean input.

Q: 4. Does it have a screaming alarm when the power goes out?

A: During a blackout, the CyberPower CP1000PFCLCD PFC Sinewave UPS System has an alarm that will sound—two short beeps, followed by a pause. However, this sound can be muted if needed.

Q: 5. How long can it power a router and modem for if the power goes out?

A: This unit is rated for a full load runtime of 3 minutes and a half load runtime of 9 minutes. It would depend on the power draw of the items you had attached to the UPS.

Q: 6. Can the Leica Q2 Protector Case be used with the Leica Q2 Handgrip?

A: No

Q: 7. Does this case come with the strap shown? Or is the strap separate/

A: No. This is just for the protector case only. The strap is a separate item and comes in different colors.

Q: 8. Does the Q2 protector case have a bottom that opens to access the battery and/or memory card, or is one sealed bottom on the case?

A: No. There is no access on the bottom of the case for either the battery or SD card. You have to remove the case to access these two areas. The bottom is solid leather with the thumbscrew in the middle to secure it to the tripod socket on the bottom of the camera.

Q: 9. Fit to 1dx mark2??

A: No, it would not. The Canon EOS 1D Mark II N DSLR camera has a 2.5-inch LCD screen; the Canon EOS 1D X Mark II DSLR camera has a much larger 3.2-inch LCD screen, and cannot use the same screen protector. The Giottos Aegis Professional M-C Schott Glass LCD Screen Protector for Canon EOS 5D Mark III / 1D X, B&H # GILSPC5D, would be the correct LCD screen option for your needs.

Q: 10. Does this have the two front usb charge ports (type-c and type-a) 3.1A?

A: No, unfortunately this item would not contain any front facing USB type-c, and type-a ports.