Stereo Amplifier For Computer Speakers 120V

Spl Performer S800 Stereo Power Amplifier With Voltair Technology (silver)

Product Code: ga182025
Availability: In Stock

$10,197.00 $15,295.50

Qty

0 reviews Write a review

Description
Reviews (0)

The silver Performer s800 Stereo Power Amplifier from SPL is an ultra-compact power amplifier. Thanks to the VOLTAiR technology, this power amplifier has absolute control over the speakers up to their load limits. In stereo operation, this bi-polar transistor power amplifier delivers up to 2 x 285W into 4 Ohms speakers. In Bridge Mode it delivers 450W into an 8 Ohms speaker. In addition, it is equipped with slave-through outputs and input trim switches.

The Performer s800 amplifier uses the VOLTAiR technology (120V rail technology) to offer a high voltage of 120V (+/-60 VDC) and large dynamic range of over 140 dB. The 120V electronics operate quasi 'idle' even at highest audio levels and impulse peaks. They never operate on the limit and therefore never get stressed. The music presents itself with serenity so that you feel pleasant when listening.

The amplifier is equipped with an 855VA toroidal transformer. The power supply is equipped with a capacitance of 40800 µF for screening and electricity storage for faithful reproduction of impulse peaks.

The Performer s800 amplifier has a protection circuit against DC voltage at the output and against overheating. At about 158°F at the heat sink, the amplifier will switch off. After the temperature has fallen below 131°F, the amplifier automatically switches on again. The temperature LED at the front indicates the overheating.

If DC is detected at the outputs, the amplifier automatically switches off. DC voltage can be an indication for a defect in the power stage. The amplifier does not automatically switch on again. It needs to be disconnected from the power (on/off). The Protect LED at the front indicates that the protection circuit is activated and the power stage has been switched off.

The amplifier is equipped with Neutrik XLR input and output connectors for balanced operation. The input signal is passively routed to the output connector to feed a second power amplifier for bi-wiring. The input can be lowered via a Trim rotary switch from 0 to -5.5 dB in 0.5 dB steps. This is useful in order to achieve an optimal stereo sweet-spot in acoustically sub-optimal rooms. In bi-wiring line-ups or in the studio with multi-speaker sets, it allows for leveling speakers with different efficiency to equal loudness.

The speaker outputs are gold plated binding post connectors. The terminals can accommodate both banana plugs, as well as a strand of up to 4mm diameter. To protect against short-circuits, the binding post is equipped with a clear plastic cap.

The Performer s800 amplifier features a 3.5mm mono jack designated as AMP CTR (amplifier control). With the appropriate cable, the amplifier can be connected to a pre-amplifier. This automatically helps in switching on the amplifier when you turn on the pre-amplifier.

Parameters
Line Inputs and Outputs	Neutrik XLR, balanced, Pin 2 = (+) Input Impedance: 10 kOhms Input Trimming: 0 to -5.5 dB in 0.5 dB steps Input Sensitivity: +6 dBu Output Impedance: Defined by connected device Crosstalk: -110 dB (@1 kHz)
Loudspeaker	Outputs 2 Pairs of binding posts with ø 0.15" (4 mm) cable hole (screwable) and banana plug Fully encapsulated
Output Power	2 x 285 Wrms into 4 Ohms 2 x 185 Wrms into 8 Ohms 1 x 450 Wrms into 8 Ohms in bridge mode
Output Voltage	74 V peak-to-peak (stereo) 180 V peak-to-peak (bridge) 35 Vrms (stereo) 86 Vrms (bridge)
Output Impedance	< 0.031, 20 Hz to 20 kHz (stereo) < 0.043, 20 Hz to 20 kHz (bridge)
Damping Factor	> 300, 20 Hz to 20 kHz, at 8 Ohms (stereo) > 190, 20 Hz to 20 kHz, at 8 Ohms (bridge)
Frequency Response	9 Hz to 100 kHz +0, -0.03 dB < 9 Hz to 200 kHz +0, -3 dB
Signal-to-Noise Ratio	> 118 dB (wide-band, unweighted, referred to full power output) > 123 dB (A-weighted)
Gain	26 dB (stereo) 32 dB (bridge)
Total Harmonic Distortion	< 0.03 % at 1 kHz, at 185 W, 8 Ohms < 0.19 % at 20 kHz, at 185 W, 8 Ohms < 0.011 % at 1 kHz, at 450 W, 8 Ohms < 0.12 % at 20 kHz at 450 W, 8 Ohms
Power Supply	Mains Voltage (Switchable): 115 VAC / 60 Hz or 230 VAC / 50 Hz Fuses: 115 V: T 8 A or 230 V: T 4 A Power Consumption: Maximum 900 VA Idle Power Consumption: 40 W
Dimensions	With Feet: 10.95 x 3.94 x 14.57" (278 x 100 x 370 mm)
Weight	28.2 lb (12.8 kg)

Bi-polar transistor power amplifier with VOLTAiR 120V technology

2 x 285W into 4 Ohms and 2 x 185W into 8 Ohms (stereo operation)

450W into 8 Ohms (mono operation - Bridge Mode)

Toroidal transformer with 855VA

40800 µF capacitance for faithful reproduction of impulse peaks

Gold-plated loudspeaker binding posts with protection covers

Neutrik XLR connectors for balanced inputs and outputs

Direct slave-through of the input (e.g. for bi-wiring)

Input trim switch for attenuation up to -5.5 dB in 0.5 dB steps

AMP CTL connector for remote power on/off switching (e.g. with Director or Phonitor x)

Overheat protection with Temp LED

DC (direct current) voltage protection with Protect LED

Related Questions and Answers

Q: 1. Will this work with 2021 M1 iPad Pro

A: Yes, you can connect the HYPER HyperDrive Power 9-in-1 USB Type-C Hub (Space Gray) to an iPad Pro.

Q: 2. Can I connect my nextbook for better sound?

A: You can hook up any audio source with an auxillary cord. I've used phones, iPads, and IPods without an issue so I'm assuming your Nextbook would be similar.

Q: 3. Will this work on a USB headset?

A: A USB headset can be connected into one the USB ports on this hub after connecting the hub to a USB-C port on a computer.

Q: 4. Does this allow microphone to be used at same time with other sound source like aux? So is it a mini mixer+amplifier likely thing?

A: Correct: Switchable MIC PAGER and MIXING ModesSet to PAGER, the signal from AUX 1/AUX 2/CD will be attenuated BY -12dB and the signal from MIC will override to page (Auto Talkover), it is good for paging system. Set to MIXING, the signals from AUX 1/AUX 2/CD and MIC will be existed at the same time, it acts like playing at KARAOKE event.

Q: 5. Can a powered subwoofer be connected to the REC OUT jacks?

A: The REC OUT on the Pyle Pro can be used with a powered subwoofer, however the signal output from this set of jacks is not affected by the master volume. If you turn down the main volume, the incoming signal is still fed to the connected device (subwoofer).

Q: 6. Will this work with iMac 24" with M1 chip (2021)

A: Yes, the HYPER HyperDrive Power 9-in-1 USB Type-C Hub (Space Gray) BH #HYHD30FG is compatible with the iMac M1.

Q: 7. if the Macbook Air has a protective case, can this device be attached to it?

A: The HYPER HyperDrive Power 9-in-1 USB Type-C Hub can operate attached to a MacBook Air with protective case.

Q: 8. I own this, but I need one with more USB ports - I think this has three and I would like one with six. Can anyone recommend or link me to one with more USB?

A: The HYPER HyperDrive Power 9-in-1 USB Type-C Hub has 3 USB 3.1 Gen 1 Type A ports and one USB 3.1 Gen 1 Type-C Port for a total of four USB ports. The APlugable UD-6950H 12-in-1 USB Type-C Dual Display Docking Station(BH #PLUD6950H) has 6 USB 3.1 Gen 1 Type-A ports. See: https://bhpho.to/3LhQ1la

Q: 9. will this work with the mb-700 mic? also will this act as a phantom power source

A: The Sabrent AU-EMAC USB External Stereo Sound Adapter (Silver) B&H # SAAUEMAC does not provide Phantom Power, therefore, it would not work with any microphone that requires Phantom Power. You would need something like this which can provide phantom power: https://bhpho.to/2TIwkfr

Q: 10. can these two channels be bridged?

A: to the best of my knowledge, no. Basic 2 channel amp, but it does what it is supposed to do well with low distortion and dependable output levels. I used it for wired speakers on my patio, Bose, that are not that efficient, but it drives them well and cleanly. Hope this helps.

There are no reviews for this product.