The NXE Series 2-Channel Networkable Multi-Mode Power Amplifier from Ashly comes pre-installed with OPDAC4 internal 4-channel DAC with selectable HPF and OPDante Dante Network Audio Interface cards. The OPDante card enables access to digital audio networks at low latencies (83.3 μs) over fast Ethernet. It can be installed in the rear card slot of nXe series amplifiers. Signal can be routed from other Dante enabled devices by simply connecting a Cat5e or Cat6 cable to the card's primary or secondary (redundant) Ethernet ports. The amplifier is capable of driving 2 Ohms loads at full power and offers a maximum rated output power of 1500W per channel at Low Z and 70V modes, and 1250W in 100V mode. In addition, the amplifier is suitable for use in performance venues, stadiums, arenas, convention centers as well as schools, store fronts, and places of worship.

The multi-mode amplifier features an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply can auto-detect 120 or 240 VAC mains, and a Neutrik powerCON is used for the AC cord. Each channel features a selectable output mode of Low Z, 70V, or 100V, an 80 Hz high-pass filter, input limiter, and input gain settings of 26 dB, 32 dB, 38 dB, or 1.4V. Each channel comes with a remote DC level control.

The amplifier comes with Neutrik XLR/TRS combo jack and Euroblock input connectors and Neutrik speakON output connectors. The unit features a front panel power switch and level controls that can be disabled. The LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. In addition, the power amplifier features an Ethernet control with a real-time clock for event scheduling.

The power amplifier is equipped with serial data remote control, aux preamp outputs, preset control, and fault condition logic outputs. It also features a temperature dependent variable speed forced-air cooling. In addition, the amplifier can be mounted on a standard 19” rack.

Ethernet control using Protea NE software

Serial data control by Ashly programmable remotes or third party controllers

Aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, optional AES3 digital audio capability, and Cobranet

Real-time clock with event scheduler

Assign automatic execution of selected functions and tasks

Event scheduler is programmed using PneS software and stored in the amplifier

Ashly remote control via iPad app for custom design of secure wireless control over a network

Features a switch-mode power supply that automatically detects 120 VAC or 240 VAC operation

Selectable outputs on each channel allow you to choose the desired output mode

Set the DIP-switch configuration for low impedance (2, 4, and 8 Ohms), or constant voltage (70V or 100V)

Ashly EMS (Energy Management System) provides an automatic sleep-mode drawing less than 1W (defeatable)

Multiple internal power supplies provide increased channel separation and reliability

Selectable 80 Hz hi-pass filter, limiter, and input gain per channel via rear panel

Remote DC level control per channel

Extensive protection circuitry and continuously variable cooling fans

Ethernet port for software control and monitoring of amplifier functions with front panel COM activity LED

Serial data port available for optional Ashly WR-5 and RD-8C programmable remote controls (optional RS-232 converter INA-1 available for third party controllers)

Instant standby mode results in 30% reduction in idle power consumption that is triggered by contact closure, software control, or event scheduler

Preset recall via contact closure, software control, remote control, or event scheduler

Programmable power-on delay

Aux preamp line outputs for driving other amplifiers

Assignable fault condition logic outputs

Neutrik Combo XLR - 1/4" TRS jack plus Euroblock input connectors

Neutrik speakON twist locking loudspeaker connectors

Neutrik powerCON detachable AC mains connector

Related Questions and Answers

Q: 1. Will this fits z50? I didnt see the battery extra?

A: No the Nikon Z50 takes different batteries.

Q: 2. Does this grip have a 1/4 female tripod hole in the bottom?

A: Yes it has a 1/4-20 tripod socket.

Q: 3. Do you need to remove the battery door cover for the grip to be attached?

A: Yes.

Q: 4. Will this work with the ftz adapter attached?

A: Yes, the FTZ adapter can still be used along with this grip.

Q: 5. Hi.. Is it good for Z7II ? Thanks

A: Yes. This will work with the Nikon Z7 II. Though this is only a battery grip. If you want controls and a shutter button, you would want the Nikon MB-N11, linked here: https://bhpho.to/2IH5gJ0

Q: 6. Can you use the usb-c port to charge the batteries in the grip using an external power bank (i.e. when you are outdoors without access to a power outlet)?

A: Yes, one can charge Nikon EN-EL15b and EN-EL15c batteries in the Nikon MB-N10 Multi-Battery Power Pack for Select Z-Series Cameras over the USB-C port on the grip. Nikon recommends only using the Nikon EH-7P Charging AC Adapter for this, though this is no longer available. One can try other methods of power, but this is not officially endorsed by Nikon. The power bank or charger would need to have enough power for this to work. Keep in mind this is only to charge the batteries, and this cannot be used to continuously power the camera.

Q: 7. Can you record video while the battery pack is also charging? Or only when camera is not recording.

A: Unfortunately, the camera must be turned off in order to charge the batteries while the grip is installed.

Q: 8. It can be used with z5?

A: The following grip will accommodate the following Z bodies. Nikon Z5 Nikon Z6 Nikon Z6 II Nikon Z7 Nikon Z7 II

Q: 9. Does this allow you to gain additional fps while shooting with it?

A: No, just longer shooting time and in grip charging.

Q: 10. Can I use EN-EL15c batteries in this?

A: Absolutely! :)