Smart Power Surge Protectors With Sleep Mode

Ashly Nxe Series 4-channel Networkable Multi-mode Power Amplifier With Opdac4 & Cnm-2 Cards

Product Code: ga182230
Availability: In Stock

$21,897.00 $26,714.34

Qty

0 reviews Write a review

Description
Reviews (0)

The NXE Series 4-Channel Networkable Multi-Mode Power Amplifier from Ashly comes pre-installed with OPDAC4 internal 4-channel DAC with selectable HPF and CNM-2 CobraNet Network Audio Interface cards. The Cobranet card enables access to digital audio networks at medium latencies (1.33 ms) over fast Ethernet. The amplifier is capable of driving 2 Ohms loads at full power and offers a maximum rated output power of 3000W per channel at Low Z mode, 2450W at 70V mode, and 1250W in 100V mode. In addition, the amplifier is suitable for use in performance venues, stadiums, arenas, convention centers as well as schools, store fronts, and places of worship.

The multi-mode amplifier features an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply can auto-detect 120 or 240 VAC mains, and a Neutrik powerCON is used for the AC cord. Each channel features a selectable output mode of Low Z, 70V, or 100V, an 80 Hz high-pass filter, input limiter, and input gain settings of 26 dB, 32 dB, 38 dB, or 1.4V. Each channel comes with a remote DC level control.

The amplifier comes with Neutrik XLR/TRS combo jack and Euroblock input connectors and Neutrik speakON output connectors. The unit features a front panel power switch and level controls that can be disabled. The LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. In addition, the power amplifier features an Ethernet control with a real-time clock for event scheduling.

The power amplifier is equipped with serial data remote control, aux preamp outputs, preset control, and fault condition logic outputs. It also features a temperature dependent variable speed forced-air cooling. In addition, the amplifier can be mounted on a standard 19” rack.

Parameters
Channels	4
Maximum Output Power	Max Output Power Per Channel, Low Impedance Output, All Channels Driven 2 Ohms: 3000 W, 4 Ohms: 2000 W, 8 Ohms: 1250 W Low Impedance Output, Bridge Mode, All Channels Driven 4 Ohms: 6000 W 8 Ohms: 4000 W 70 V, 100 V Output, All Channels Driven 70 V (per channel): 2450 W 100 V (per channel): 1250 W
Power Draw	Total Power Draw All Channels Driven Sleep Mode: <1 W Standby Mode: 70 W Idle (no signal): 100 W
Current Draw	Current Draw 120 VAC Mains (divide in half for 240 V) Sleep Mode: 0.1 A Standby Mode: 1.3 A Idle (no signal): 1.85 A Maximum Current Draw All Channels Driven, Divide by 2 for 240 VAC 1/8 Maximum Power @ 2 Ohms: 29.5 A
Dissipation	Thermal Dissipation BTU/hr, Total for All Channels Driven Sleep Mode: <3.4 Standby Mode: 238 BTU/hr Idle (no signal): 340 BTU/hr 1/8 Maximum Power @ 2 Ohms: 2720 BTU/hr
Voltage Gain	Selectable at 26 dB, 32 dB, 38 dB, or 1.4 V
Damping Factor	>250 (8 Ohms load <1 kHz)
High Pass Filter	Input: 80 Hz 2nd order
Distortion	SMPTE, typical: <0.5% THD-N, typical: <0.5% (8 Ohms, 10 dB below rated power, 20 Hz to 20 kHz)
Channel Separation	-75 dB (dB from full output, 1 kHz)
Signal-to-Noise Ratio	20 Hz to 20 kHz, Unweighted: >114 dB
Frequency Response	20 Hz to 20 kHz, +/-0.05 dB
Input Connector	Balanced: Euroblock 3.5 mm, 1/4" TRS and XLR combo jack
Input Impedance	10 kOhms
Maximum Input Level	+21 dBu
Output Connector	Speaker: Neutrik speakON AUX: Balanced Euroblock 3.5 mm
Network	Control Network: Compatible with standard 100MB Ethernet
Aux Output Level	Maximum: +21 dBu
Contact Closure	Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
Supported Data Connections	Euroblock 3.5 mm - Gnd, +18 V, In, Out
Logic Output	Fault Condition: Euroblock 3.5 mm - 4 available
Level Control	Remote DC: Euroblock 3.5 mm - Gnd, CV, V+ per input
Active Attenuators	Per Channel: Front panel, software, offset link group, and remote Fully Off: Mute
Amplifier Protection	Inrush current limitation, temperature monitoring, output over-power protection, mains fuses
Cooling	Continuously variable temperature controlled axial fan(s)
Environmental	32 to 113°F (0 to 45°C) (non-condensing)
Front Panel LED Indicators	POWER (white): Switch: On, Off, Standby (flashing) PROTECT (red): On (fault condition or shut down), Off SLEEP (blue): On, amplifier is asleep from audio inactivity DISABLE (yellow): On, power switch & front panel attenuators are disabled Per Channel CLIP/MUTE (red): Clip @ 1 dB below full output / Mute SIGNAL (green): -18 dB below rated output CURRENT (green): Proportional to output TEMP (yellow): On dim at 90% max operating temperature, full bright + protect at 100% BRIDGE (green): On, Off
Power Requirements	@ 50/60 Hz Nominal (Automatic Sensing SMPS): 120 to 240 VAC Operating Range: 70 to 135 VAC to 140 to 270 VAC Minimum Power-Up: 85 to 170 VAC Power Cable Connector: 20 A powerCON
Compliance	cTUVus, CE, FCC, RoHS
Dimensions	19 x 3.5 x 16.84 (483 x 89 x 428 mm)
Weight	28.7 lb (13 kg)

Ethernet control using Protea NE software

Serial data control by Ashly programmable remotes or third party controllers

Aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, optional AES3 digital audio capability, and Dante

Real-time clock with event scheduler

Assign automatic execution of selected functions and tasks

Event scheduler is programmed using PneS software and stored in the amplifier

Ashly remote control via iPad app for custom design of secure wireless control over a network

Features a switch-mode power supply that automatically detects 120 or 240 VAC operation

Selectable outputs on each channel allow you to choose the desired output mode

Set the DIP-switch configuration for low impedance (2, 4, and 8 Ohms), or constant voltage (70V or 100V)

Ashly EMS (Energy Management System) provides an automatic sleep-mode drawing less than 1W (defeatable)

Multiple internal power supplies provide increased channel separation and reliability

Selectable 80 Hz hi-pass filter, limiter, and input gain per channel via rear panel

Remote DC level control per channel

Extensive protection circuitry and continuously variable cooling fans

Ethernet port for software control and monitoring of amplifier functions with front panel COM activity LED

Serial data port available for optional Ashly WR-5 and RD-8C programmable remote controls (optional RS-232 converter INA-1 available for third party controllers)

Instant standby mode results in 30% reduction in idle power consumption that is triggered by contact closure, software control, or event scheduler

Preset recall via contact closure, software control, remote control, or event scheduler

Programmable power-on delay

Aux preamp line outputs for driving other amplifiers

Assignable fault condition logic outputs

Neutrik Combo XLR - 1/4" TRS jack plus Euroblock input connectors

Neutrik speakON twist locking loudspeaker connectors

Neutrik powerCON detachable AC mains connector

Related Questions and Answers

Q: 1. Will this fits z50? I didnt see the battery extra?

A: No the Nikon Z50 takes different batteries.

Q: 2. It holds two batteries but you give up the camera's battery spot by installing the MB-N10 so it actually ads only one more battery total, correct?

A: That is correct, the grip allows you to use 2 batteries, not 3.

Q: 3. Can I use EN-EL15c batteries in this?

A: Absolutely! :)

Q: 4. Do you need to remove the battery door cover for the grip to be attached?

A: Yes.

Q: 5. How much height does this grip add to the Z6/Z7? I am trying to determine if using this grip might require me to find a new camera bag. Thanks!

A: The grip adds just about 2".

Q: 6. Will this work with the ftz adapter attached?

A: Yes, the FTZ adapter can still be used along with this grip.

Q: 7. It can be used with z5?

A: The following grip will accommodate the following Z bodies. Nikon Z5 Nikon Z6 Nikon Z6 II Nikon Z7 Nikon Z7 II

Q: 8. Will is still fit if I am using a smallrig or any other camera cage?

A: The Nikon MB-N10 Multi-Battery Power Pack for Select Z-Series Cameras would not be compatible with a camera cage.

Q: 9. There is a usb-c port on the back of the unit. Will this allow wall power of the unit (with appropriate cables etc)? I see in another question it won’t charge the batteries, can it be used to power from the wall with/without batteries?

A: The usb port is to charge the batteries in the grip when using the EH7-P charging adapter.

Q: 10. Does this come with any batteries? Or are those separate?

A: The required batteries are not included with this grip. https://bhpho.to/367zzPx

There are no reviews for this product.