The 1200W Crown Audio CDi 4|1200 4-Channel DriveCore Series Power Amplifier utilizes technology derived from the flagship Crown DriveCore Install series amplifiers, providing an impressive mix of high-performance, rich feature set, and competitive cost. The CDi DriveCore 4|1200 offers streamlined functionality for most large-sized installation such as cinema, houses of worship, hotels, cruise lines, and more.

The DriveCore integrated circuit eliminates hundreds of components within the amplifier, reducing the variability of component values and increasing reliability, resulting in remarkable audio fidelity from an efficient design. The 4-channel amplifier is simple to use and includes a network control & monitoring, an advanced DSP circuit, and an easy-to-use, front-panel interface.

The amplifier is capable of driving up to 100Vrms speaker loads without requiring a transformer and comes pre-loaded with JBL speaker tunings to help make installations quicker and easier. The CDi 4|1200 features an Ethernet port for using HARMAN's HiQnet Audio Architect software for configuration and operation over a standard TCP/IQ network. The rear panel includes terminal block inputs and barrier strip outputs.

DriveCore Technology    Remarkable Performance & Reliability    Supports HiQnet Audio Architect Software    Monitor & Control over Standard TCP/IP    Color LCD Panel for Control & Monitoring    Advanced DSP on Inputs & Outputs    Works with 70V & 100V Speakers    Universal Power Supply    2 Terminal Blocks Included    Included Power Cord

• DriveCore Technology: patented DriveCore integrated circuit combines hundreds of discrete circuits into one chip for better performance, lower power consumption, and improved reliability
• Supports configuration and control using HiQnet Audio Architect
• Monitoring and control over TCP/IP
• Color LCD and front-panel user interface for amplifier configuration, control, and monitoring
• Programmable GPIO (general purpose input/output) control port
• Digital signal processing (input/output EQ filters, crossover, input/output delay, LevelMAX limiters)
• Support for importing of FIR filter coefficients
• 20 device presets—1 factory and 19 user
• 96 kHz/32-bit floating-point signal processing
• Universal power supply with PFC for reduced current draw and industry-leading efficiency
• Power saving modes
• Remote power off—Sleep mode activated via AUX port
• 70/100Vrms direct drive
• Each channel independently configurable for low z or high z operation
• Advanced protection circuits—amplifier and loads are protected against shorted outputs, DC, mismatched loads, overheating, over/undervoltage, and high-frequency overload
• Three-year, no-fault transferable warranty—your investment is fully protected
• Complies with GreenEdge by HARMAN—environmentally friendly practices in design, manufacturing, and packaging complement energy-efficient operation
• Support for BSS Audio Soundweb Contrio Ethernet wall controllers
• Included speaker tuning for various JBL speaker models

Related Questions and Answers

Q: 1. If the output is equal to 1200 watts tungsten, but has daylight output at 5200+/-, is it like a 1200 watt HMI?

A: The Genaray MonoBright Daylight LED 1200 has the equivalent output of a 1,200W open-face tungsten light. HMI lights of equivalent wattage have much higher outputs compared to tungsten lights as they are much more efficient, so no, a 1,200 watt-equivalent tungsten (or tungsten-equivalent) light would not be anywhere as bright as a 1,200 watt HMI light source. 5200K is the light source's Kelvin color temperature; as daylight at noon is typically 5600K, so light sources that have an output of 5000-6500K are considered to have a daylight-balanced color temperature. Kelvin temperature, wattage, and light output are all different things and cannot be directly compared to one another.

Q: 2. How hot do these lights get? Would you be able to use standard silver or white soft boxes or would you need to use a quartz or high heat option?

A: It stays relatively cool. Probably close to 110F to touch (cooler than hot water).

Q: 3. How does the power compare to an Aputure 120D COB?

A: According to the photometrics, the Genaray MonoBright Daylight LED 1200 would be more powerful compared to the Aputure Light Storm LS C120d light fixture. The Genaray light fixthre has an output of 14,000 Lux / 1300.6 FC measured at 3 feet / 1 meter, while the Aputure light fixture has an output of 3,300 Lux / 306 FC measured at 3 feet / 1 meter.

Q: 4. this led light good for film shoot?

A: Depending on your shoot, yes. Ive been very happy with these so far. Last week I shot in a room with open windows and a skylight in daylight and they still did the job. Very happy with these.

Q: 5. Hi, What are the differences between 'Hi-Sync' Vs 'Pro' flash heads ?

A: It's flash duration. The Hi-Sync heads have a longer flash duration which provides a greater window for the shutter to synchronize at higher speeds.

Q: 6. Can I use bowens mount modifiers with this unit?

A: Yes this will work with Bowens mounts.

Q: 7. Are Preamp outputs volume controlled with the master volume control as well as the PreOut level control knob?

A: Preamp controls each channel individually, and the master controls the summed signals.

Q: 8. How can I connect a battery to the Genaray to use in the woods at night for several hours ?

A: With a power xlr to v mount or other batter adaptor

Q: 9. What is how may RMS per channel this item?

A: The RMS power isn't listed by the manufacturer.

Q: 10. Sorry if I'm just missing this info on the page, but how long is the power cable?

A: Approximately 12 ft