The TPE-5048WS 48-Port PoE+ Compliant Gigabit Managed Switch from TRENDnet delivers advanced management features with a 104 Gb/s switching capacity. This rack mountable IPv6 ready switch comes with an intuitive web-based interface. Advanced traffic management controls, troubleshooting, and SNMP monitoring make this a powerful solution for SMB networks. The TPE-5048WS provides 48 Gigabit PoE+ ports with a total power budget of 740W, and four shared Gigabit RJ45 / SFP combo ports. The PoE+ standard supplies up to 30W of power per port for devices such as high power wireless access points, PTZ (Pan Tilt Zoom) cameras, and VoIP telephony systems.

48 x Gigabit Ethernet PoE+ Ports    4 x RJ45 / SFP Combo Ports    104 Gb/s Switching Capacity    77.4 Mpps Forwarding Rate    740W Power Budget    Rackmount Design    Fan Cooling

Related Questions and Answers

Q: 1. Can one assign different devices on the LAN to specific WAN connections, eg via a routing table?

A: You can setup routing tables with the TRENDnet TEW-829DRU AC3000 Wireless Tri-Band Gigabit Router BH #TRTEW829DRU.

Q: 2. Will this suit a Fuji X-T5, and not obstruct the battery door to prevent it from fully opening?

A: This plate will not interfere with the battery door on the xt5

Q: 3. Regarding the 48" Boom Arm. Is each section or arm 48" long or is that the total length?

A: The total length of the MBA48 boom arm is 48".

Q: 4. Does this have a soft top to it (so it's not hard metal against the camera)?

A: There is a rubber grip on the top of the plate that keeps the plate in place without scratching the camera body.

Q: 5. What do I need to connect this to my Godox AD200?

A: To connect this Luxbanx Large Rectangular Softbox, you would need the Impact Speed Ring for Impact, Bowens S, Westcott & Aputure, BH #IMSRIMPV and the Godox S2 Speedlite Bracket for Bowens, BH # GOS2. https://bhpho.to/3gOT7TT https://bhpho.to/3a4S7Dv

Q: 6. What is the diameter of the flange mount?

A: We have requested this information from the manufacturer but accurate measurements are not readily available. We will post the details once we receive them.

Q: 7. Will this unit work without a USB host? For example, can I use this as a pre-amp, and the headphone output directly to a recorder, without having this plugged into a computer? I'd be powering the unit via a USB power supply.

A: It requires a USB host.

Q: 8. How do you factory reset the adapters?

A: On the bottom of the device you should see a reset button, stick a small pin inside and hold down for 10-15 seconds. This should reset the device to factory settings

Q: 9. Can this modifier be used with a Bowen’s S mount as well as a speed light?

A: Unfortunately, this particular series of softbox would not have a Bowens S attachment for it.

Q: 10. Does the TRENDnet TEW-829DRU support load balancing and failover at the same time? Or would load balancing just handle the case of a dead WAN?

A: Hi Einar! Thanks for your interest in TRENDnet! If you put the router in load balance mode and one of the connections fail it will continue to route traffic out the connected WAN. As long as you don’t have any specific device setup to router out the down WAN connection. Hope this helps! If you have any more questions, you can always respond directly to this thread and someone will be happy to try and help answer any additional questions you may have! Have a great day! Adrian TRENDnet CS