The WindTech PPA-01 is an adapter system designed to provide an affordable method for extending your reach when holding a microphone, camera, or antenna in location recording, electronic news gathering, and television production. It is designed to be used with a painter’s extension pole, and can also work with some broom handles.

The Acme 3/4"-5 female end attaches to your pole, and the adapter enables you to convert to a 5/8"-27 male thread type. The adapter offers confirmed compatibility with the following poles: Wooster Sherlock, Mr. Longarm, Linzer Pro Everlock, Unger Pro Line, Lowe's Quickie Pro, and Home Depot 5' extension poles. It is advised to test the adapter prior to purchasing a pole.

Extend the Height of a Camera or Mic    Use with Painter's Extension Poles    Acme 3/4" -5 Female End Attaches to Pole    Converts to 5/8"-27 Male

Extend the height of a camera, antenna, or microphone

Designed for use with painter's extension poles

Works with some broom handles

Acme 3/4" -5 female end attaches to pole

Related Questions and Answers

Q: 1. Is this compatible to the Go Pro Hero 8 Black?

A: Yes. The Ulanzi Mini Extension Pole Tripod for GoPro Action Camera will work for the GoPro Hero 8 Black.

Q: 2. Is this 4k capable? HDMI 2.0 or a 1080 cable?

A: This cable will pass a 4K signal.

Q: 3. Can i use it with manfrotto 1004bac?

A: When using the Manfrotto 3-Section Extension Pole (35- 92") (Black) BH #MA099B you need to consider the load your attaching and if it will exceed the stands load limit and if the stand has a welded tip or a pressed on tip. The pressed on tips do not have as much strength for off axis loads. That 1004BAC has a load limit of 19lbs and a pressed on tip.

Q: 4. is this made of plastic?

A: The Windtech CM 58 is a plastic mount. We do carry some similar products that are brass such as the Windtech CM57 and the Audio Technica AT8469.

Q: 5. What is the outside diameter of each of the carbon fiber tubes?

A: One section of the Sunwayfoto ET-01 Carbon Fiber Tripod Extension Tube is 24mm in diameter, and the other section is 20mm in diameter.

Q: 6. la extension se acopla a la manija Osmo? para accionar el telefono?

A: The grey cellphone holder that comes with the OSMO attaches to the handle on this Extension Pole. The OSMO connects to the Extension Pole in the place where the grey cellphone holder usually goes on the OSMO handle. The cellphone connects to the OSMO through the OSMO's wifi. The pole is good quality and compatible with the OSMO. Connections fit tightly together. I hope that answers your question, I used google translate :)

Q: 7. Does this come with both of the additional silver adapters shown in photo?

A: The WindTech PPA-02 ships with Pole adapter as well as both the 3/8 and 1/4 adapters shown.

Q: 8. Is it really sure that this Kupo 3-Section Extension Pole is not compatible with the Kupo Slider Stand (Black, 45.3 ") + Kupo Baby Ball Head Adapter ..?

A: Hi Daniel, The Kupo Slider Stand top has a junior receiver i.e. female 1-1/8inch; The Extension Pole ends are threaded 3/8” - male on one end female on the other. The Kupo Baby Ball Head Adapter would allow the 3-Section Extension Pole to be connected to the Kupo Slider Stand. You would just need to remove the t-handle from the Ball Head Adapter so it drops into the stand top opening, and then screw on the Extension Pole https://www.bhphotovideo.com/c/product/1244788-REG/kupo_kg014212_baby_ball_head_adapter.html

Q: 9. The unit ships with a 3/8" adapter and acorn nut installed on the top section. How do you remove the 3/8" threaded adapter on the top section to expose the 1/4"x20 threaded post?

A: The top thread on the Sunwayfoto ET-01 Carbon Fiber Tripod Extension Tube is reversible. One side is 3/8th inch and the other is 1/4 inch.

Q: 10. If I use a removable 1/4-20 thread on this 3/8 thread, can I use 2 of this item with the Manfrotto 272B Adjustable Background Holder (I dont know what mean Type-25 attachment)? Thanks for your help.

A: If you want to use the stand extension to make the Manfrotto 272B cross bar longer, that is not designed to do that.The cross bar can attached to many light stands. Most stands have a 5/8 male stud connection and the cross bar will fit that.