This beige, ultralow-profile Microphone Madness MM-PSM-s Short Boom Pro Series Omnidirectional Earset Mic delivers clear spoken-word and vocal reproduction for presenters and performers working in music, theatrical, broadcast, house of worship, lecture, and presentation settings. It comes with a TA3F connector that plugs into select Samson bodypack transmitters.

The MM-PSM-s Short Boom Pro Series earset features a 3mm capsule mounted on a very-short 1.25' boom that provides a tight fit with no movement while discreetly positioned away from the mouth for an unobtrusive fit. The lightweight earset can be worn on either the left or right ear and feels natural when used for extended periods of time. The extremely flexible boom is virtually unbreakable.

The capsule delivers full-frequency (20 Hz to 20 kHz) audio performance and high gain before feedback for detailed speech intelligibility. The 145 dB of dynamic range makes this mic well suited for loud vocal performances in houses of worship and on the musical stage. The mic's omnidirectional polar pattern offers enhanced plosive protection with no proximity effect for a natural sound.

All MM-PSM-s Short Boom Pro Series microphones are made in the USA.

For Stage, Broadcast, Public Speaking    Omnidirectional Pickup Pattern    1.25" Boom/Low-Profile/Single-Ear Design    TA3F Connector    Made in the USA

• TA3F connector for compatibility with the following Samson wireless transmitters: AL-300, CT3, CT7, VT2L, VT3L, UT1L, and T32

Related Questions and Answers

Q: 1. Is Samson SP04 Shockmount compatible with this mic stand?

A: Yes, both the stand and mount use 5/8" threading.

Q: 2. What is the actual weight of this mic stand?

A: Samson doesn't specify the weight of the mic stand on their specs sheet, but this BL3 stand weighs about 5 lbs.

Q: 3. Would this work if I attached the flange mount to the wall? Or are the joints going to be incompatible with that 90 degree orientation change?

A: This product is desined fr table mounting in the orientation shown.

Q: 4. Does the joint at the mic maintain it's angle as you move the boom arm? Or do you have to reposition the mic each time the boom arm is moved?

A: The action of the spring inside the arm maintains a proportionate angle between the bottom and middle joints. Due to the nature of the spring-loaded arm, the joints do not naturally move independently of each other. It is however possible to keep the arm steady during adjustment without too much difficulty, and each joint can be manually adjusted if the opposite section is held in place with your other hand.

Q: 5. IS there a deeper clamp available for desks with a beveled edge?

A: The O.C. White Ultima 4-Way Modular Clamp Assembly for Ultima ULP Microphone Boom (B&H # OCULPCLAMP) looks like it is deeper and heavier than the Samson clamp. The inside diameter of the hole on the O.C. White clamp is 17mm. Here is a link for the manufacturer's info page: https://www.ocwhite.com/product/ultima-ulp-clamp/

Q: 6. Can this be used to mount a small camera? What's the weight capacity of this arm?

A: The arm would be used with microphones less than 2 lbs in weight. Be aware that the threading is 5/8"-27. Use this adapter: WindTech M19 5/8"-27 Female to 1/4"-20 Male Adapter BH #WIM8219: https://bhpho.to/2w6kEs5

Q: 7. Will c-clamp fit 4 cm thick table?

A: The c-clamp will fit a 4cm thick table.

Q: 8. I want to make sure this is tall enough to reach over my monitor, I appears in the photo the section from the clamp to the elbow is equal in length to the section from the mic to the elbow, so is each section 28 inches in length or is it 28 inches from desk to mic measuring both sections together?

A: The total length of the entire arm (both sections) is 28". Samson does offer two options for longer arms with the same design. The MBA38 (B&H # SAMBA38) is 38" long and the MBA48 (B&H # SAMBA48) is 48" long. Both models are available in stock and ready to ship.

Q: 9. How does the quality of this compare to the Rode PSA1?

A: The quality of this studio boom arm would be similar to the Rode PSA1 Studio Boom Arm for Broadcast Microphones, BH #ROPSA1, but it has a shorter reach of 28-inches fully extended.

Q: 10. Does this fit into the FS5 mic holder?

A: No, the mic holder on the camera is larger than the diameter of the microphone, but this is not uncommon at all. You will use a couple of rubber O-Rings to give the mic enough girth to snugly fit into the holder. https://www.bhphotovideo.com/c/product/341475-REG/Sanken_ROCS_ROCS_Rubber_O_Rings_f_CS_1.html