This Cable Technologies CT-LPS33-24K is a low-profile LPXLR-3F to TA3F cable designed to connect Lectrosonics UCR-type receivers into Sound Devices mixer/recorders like the 633, 688, 788T, and more. Colored black for easy distinguishing, the cable uses low-profile XLR connectors, with an adjustable outlet that lets you set the orientation to the left or right of the release pin. These features allow for multiple placement possibilities, all while reducing the visible profile of interconnect panels. This results in a less cluttered look all around.

The cable diameter is relatively slim at 2.7mm, though its flexible polyurethane jacket is crush resistant, tear-resistant, and resistant to cold weather. This cable measures 24" in length.

For Lectrosonics UCR Receivers    For Sound Devices Mixers/Recorders    24" Length    Color-Coded for Easy Identification    Adjustable Outlets    Angle-Adjustable    Flexible & Strong Polyurethane Jacket    Crush-, Tear- & Cold-Resistant    2.7mm OD Cable Jacket

Lectrosonics UCR type receivers
Sound Devices 633, 688, 664 (CL-6), 788T, and other compatible gear

Related Questions and Answers

Q: 1. Does this regulate voltage to a safe 7.6V from Vmount batteries of 14.4V?

A: I have been using it for a few weeks now with no issues attached to Nano 14.8V vmount batteries.

Q: 2. Does this work with A7siii?

A: Just to provide even more clarification due to conflicting answers: no, this will not work with the A7SIII. This model is for the A7II-generation and A6000-series cameras (except the A6600).

Q: 3. Will this work with the power pod 14.4 volt station and covert to the appropriate 7.2 volts or should I use the 7.2 volt power pod?

A: You can do either way. However, I think I would lean to the two battery 7.2 because you get the ability to hot swap out a dead battery.

Q: 4. Does this work with the Sony A6500

A: Yes it should. The A6500 uses the same battery as the NP-FW50 style battery as the cameras listed, it should work as well.

Q: 5. is there a way to run this with a normal quick charge power bank?

A: ive had success with both Xtpower banks off amazon. You will need a 2.5mm to 2.1mm adapter and add some copper in the center connector. The two indipro battery cables i ordered, the inner connector was deeper then the adapters and xtpower banks so it wasnt a solid connection and only worked sometimes. The copper fixed it and made it reliable. Worked great. ran the A7sII through hdmi for a live feed off a 20,000 milamp xtpower battery for 4hours and battery showed 73% left.

Q: 6. Can i run this off a usb power bank? ... if so where can i find the 2.5mm power to usb port cable?

A: The USB power bank has to have an output of 7.4 volts or more. If it is a standard 5vdc usb output, it will not work. Your camera requires 7.4vdc to operate.

Q: 7. Does this work with Sony a7R V?

A: Yes, the ZILR USB Type-C to Sony NP-FZ100 Regulated Dummy Battery Cable will work with a Sony a7R V unit.

Q: 8. Will this work on the GT2 guitar trainer?

A: No, the unit was designed to be used with the RC-30P footswitch.Since the TASCAM RC-30P is no longer manufactured (with no replacement), any momentary closure, NO (normally open) foot-switch using a 1/4 phono plug can be used.Examples: * BOSS FS-5U* M-AUDIO SP-1Thank you for your interest in TASCAM products.

Q: 9. Would this plug into the DSLR 15mm Rod Clamp NP-F970 or F550 Battery Power Supply E6 Coupler??

A: Even if it fit I would not recommend using it in that manner. This is a unregulated adapter an you can easily fry a camera is the voltage is not correct.

Q: 10. I have an 8v output on a battery plate, but the camera is 7.2. Will this be safe?

A: This cable is compatible with 7.2 - 8V sources. It will be safe.