This Cable Technologies CT-LPS33-24P is a low-profile LPXLR-3F to TA3F cable designed to connect Lectrosonics UCR-type receivers into Sound Devices mixer/recorders like the 633, 688, 788T, and more. Colored purple for easy distinguishing, the cable uses low-profile XLR connectors, with an adjustable outlet that lets you set the orientation to the left or right of the release pin. These features allow for multiple placement possibilities, all while reducing the visible profile of interconnect panels. This results in a less cluttered look all around.

The cable diameter is relatively slim at 2.7mm, though its flexible polyurethane jacket is crush resistant, tear-resistant, and resistant to cold weather. This cable measures 24" in length.

For Lectrosonics UCR Receivers    For Sound Devices Mixers/Recorders    24" Length    Color-Coded for Easy Identification    Adjustable Outlets    Angle-Adjustable    Flexible & Strong Polyurethane Jacket    Crush-, Tear- & Cold-Resistant    2.7mm OD Cable Jacket

Lectrosonics UCR type receivers
Sound Devices 633, 688, 664 (CL-6), 788T, and other compatible gear

Related Questions and Answers

Q: 1. Can i use this for sony a7s ll

A: Yes you can use with a7s2

Q: 2. Does this work with Sony a7R V?

A: Yes, the ZILR USB Type-C to Sony NP-FZ100 Regulated Dummy Battery Cable will work with a Sony a7R V unit.

Q: 3. I was looking for an external battery / portable charger to power my A7R2 in the field when shooting extended timelapse series. I see the voltage range of this adapter, but what is a recommended amperage range? Additionally, can anyone recommend a good battery that isn't too large that might get the job done?

A: I Cut the DC coupler/connector off the end and connected this to a lawnmower battery for a 9 hour long overnight timelapse with my sony a7s2. Readying the output voltage with a meter from a standard fully charged sony battery, and the output voltage from this adapter attached to the lawnmower battery, both voltages were the same. I have had no issues since with this setup and have used it many times now. If it works with a 12v lawnmower battery, I'm sure you will be fine with whatever battery you use, Just be sure to check the voltages from the adapters output before plugging it into your camera for the first time to make sure everything stays stable and steady and that you dont have a defective adapter.

Q: 4. can this be used to power a7sii with zhiyun crane 2 power output?

A: Included in the box is a cable that can charge the Sony camera. However, you cannot charge and control at the same time according to ZhiyunTech.

Q: 5. Is it fully decoded so the camera show the battery capacity?

A: Yes, it is full decoded. This cable includes a smart chip in the dummy battery that communicates with the camera to show the battery capacity as well as other information.

Q: 6. How to return

A: If you wish to return or exchange within 30 days of purchase from B&H, please contact our Customer Service department. Please see the following link. https://bhpho.to/2caRE5L

Q: 7. is there a way to run this with a normal quick charge power bank?

A: ive had success with both Xtpower banks off amazon. You will need a 2.5mm to 2.1mm adapter and add some copper in the center connector. The two indipro battery cables i ordered, the inner connector was deeper then the adapters and xtpower banks so it wasnt a solid connection and only worked sometimes. The copper fixed it and made it reliable. Worked great. ran the A7sII through hdmi for a live feed off a 20,000 milamp xtpower battery for 4hours and battery showed 73% left.

Q: 8. Can i run this off a usb power bank? ... if so where can i find the 2.5mm power to usb port cable?

A: The USB power bank has to have an output of 7.4 volts or more. If it is a standard 5vdc usb output, it will not work. Your camera requires 7.4vdc to operate.

Q: 9. Will this work with the Xt-20?

A: This d-tap regulation cable should work with the FUJIFILM X-T20 camera as it uses the same FUJIFILM NP-W126S battery which is the same dummy battery on this cable.

Q: 10. Does this regulate voltage to a safe 7.6V from Vmount batteries of 14.4V?

A: I have been using it for a few weeks now with no issues attached to Nano 14.8V vmount batteries.