ARRI's LMB 6x6 Tilt and Flex Adapter 80-156mm can be used to bridge any gap between extending front elements on your lens and an LMB 6x6 matte box. This adapter is compatible with lenses incorporating a front outer diameter between 80 and 156mm.

The Tilt and Flex Adapter will also compensate for the tilting angle created when using a Swing-Away Tilt Module with the LMB 6x6 matte box. An interface at the bottom of the adapter can accommodate either the LMB 15mm or LMB 19mm Studio Rod Adapter.

For LMB 6x6 Matte Box    For 80 to <156mm Lens Diameters    LMB 15 & 19mm Rod Interface    Flexible Rubber Donut    Compatible with ARRI Tilt Modules

Fits lenses with diameters between 80 and 156mm

Bridges gap created by a lens with extending front elements or by a Swing-Away Tilt Module

Integrated rod interface for 15 or 19mm rods

Related Questions and Answers

Q: 1. Is device compatible with Sony A7RIII for remote trigger? If so does it require a cable from device to camera?

A: To trigger the A7R III remotely, you would need one of these units connected with the Vello 3.5mm Remote Shutter Release Cable for Select Sony Cameras with Multi-Terminal, BH #VERCCS235, while the second Impact unit is the transmitter in your hand. https://bhpho.to/2GvqNAr

Q: 2. Will these work on a sony A7 II and a YN560-II speedlite?

A: Yes. I have both and it works with both.

Q: 3. I have a PowerSync10 transmitter. Is this compatible?

A: Unfortunately, this unit is not compatible with the Impact PowerSync 10 transmitter.

Q: 4. Does this adapter work with the Nisi Athena lenses?

A: The Metabones Lens Mount Adapter for ARRI PL-Mount Lens to FUJIFILM X-Mount Camera and it is advised to use the NiSi made adapters for their lenses.

Q: 5. Can I use this transceiver with Elinchrom D-Lite 400W/s RX 4 Flash Head?

A: If you had 2 of these transceivers you could use it with the Elinchrom D-Lite 400W/s RX 4 Flash Head. The Impact PowerSync 16-80 will not fire the internal receiver on the Elinchrom. You need to have 1 PowerSync 16-80 attached to the 3.5mm sync port of the Elinchrome and 1 PowewerSync 16-80 on the camera.

Q: 6. Is this a solid piece of fabric or are there seams running across the face of the diffuser?

A: There no seam, it's one piece of cloth.

Q: 7. With the built-in 2x extender engaged, will it cover a S35 sensor (Alexa)?

A: Yes it will, this covers a Super 35mm with a lens that has a 2x extender engaged.

Q: 8. Good day, may I know if this transceiver support HSS and TTL? I also want to believe it should be able to work with old Minolta/Sony flash like the 5600 HS Shoe Mount Xenon Flash (For Minolta) and Sony ILCA-A77M2 while also using the necessary adapters like the TF-323 SONY & Minolta TTL Hot Shoe to PC Sync Adapter.

A: The Impact PowerSync16-80 Transceiver is a fully manual transceiver. It does not have TTL or high Speed Sync capabilities. As the Minolta 5600HS Flash does not have a PC sync terminal, you would need to purchase a hot shoe adapter such as the Vello HSA-CSMSA Multi-Interface to Sony/Minolta Shoe Adapter, B&H # VEHSACSMSA, to connect the Impact PowerSync 16-80 Transceiver to the Minolta 5600HS Flash.

Q: 9. Will this work with the Sony PMW-F5?

A: Should work:The MTF Services Ltd B4 2/3 to Arri PL Adapter allows the use of B4 lenses on PL mounted cameras.Note: Can only be used on B4 2/3 lenses with built-in 2x extender engaged, HD lenses recommended.

Q: 10. Does this fabric have grommets for tieing to frames?

A: The fabric does have grommets for securing the fabric to a frame.