The Oval Ultra Small Viewfinder Eyecushion in black Ultrasuede, from Bluestar, features outside dimensions of 3.3 x 2.6" to securely fit over many common external and built-in viewfinders. These include the Hoodman Hoodeye, JJC Oval Shape EyeShade, JJC Viewfinder, Bolex H16, and the viewfinder of the Panasonic GH5 with a compatible oval eyecup similar to the Hoodeye. This Ultrasuede version is made of 100% non-woven material consisting of intertwined, brushed, ultra-fine fiber strands. It provides a high level of softness and a superior moisture absorption rate, and it can be used in any climate.

3.3 x 2.6" Outside Dimensions

Related Questions and Answers

Q: 1. Would this be a good fit for the Canon RF 16mm f/2.8 STM Lens with lens hood - or would it be too large?

A: The Lowepro case would be to large for the Canon 16mm f2.8 RF lens. This Ruggard would be a better fit: https://bhpho.to/3jMEnq4

Q: 2. Will a cannon 100mm f2 fit in the Lowepro LP36977 case?

A: Yes, the 100mm f/2 will just fit.

Q: 3. Will this case (7x8cm) fit for: Nikon AF-S NIKKOR 50mm f/1.4G Lens /OR/ there is a better Lowepro alternative? THANKS

A: Yes, it will fit the Nikon 50mm 1.4.

Q: 4. Are the dimensions listed interior dimensions of the products?

A: The dimensions are:Exterior: 3.5 x 4.1 inches 9.0 x 10.5 cmInterior: 3.2 H x 3.0 W x 2.8 L inches 8.0 x 7.5 x 7.0 cmThis information is on its web page. Expand the Specifications area

Q: 5. will this fit a ef 50mm 1.8 stm with the lens hood?

A: It would fit, but would be tight with the hood. If you want a bit looser fit, the Lowepro 9 X 9cm might be the better option.

Q: 6. Will this fit a Sony SEL1018?

A: The Lowepro Small Lens Case 7x8cm (Black) interior is 3.0 x 2.8 x 3.2 / 7.5 x 7.0 x 8.0 cm. The Sony E 10-18mm f/4 OSS Lens is 2.76 x 2.50 (70 x 63.5 mm). The numbers say a perfect fit.

Q: 7. Is this a good fit for a Sony 35mm f1.8?

A: This definitely fits the Sony 35mm f/1.8.

Q: 8. Will this fit a Nikon AF-S DX NIKKOR 55-200mm f/4-5.6G ED VR II Lens?

A: I use it with a Sony Zeiss 55 mm 1.8 in fact the lens case could be a little shorter, but I'm very pleased with it. Excelent built quality.

Q: 9. How do I attache the reflector?

A: Excellent question, because the attachment is somewhat flimsy. The two outer pieces( that protrude away from the ends of the main shaft) push against the reflector. You create a slight compression on the reflector by sliding the holders inward, then tightening the two knobs in the center of the shaft to maintain the compression. There is a little spring clip in the two holders that helps hold the reflector, but just barely. I've been able to make this work in a studio, but if anyone bumps it, or creates a breeze, the reflector will fall off. You cannot rotate the reflector without it falling off. This means one of the ends of the holder needs to be attached to the highest elevation part of the reflector and the other holder needs to be attached at the lowest elevation part of the reflector. There is a real opportunity for someone to design a better reflector holder - specifically the two pieces on the ends of the shaft. I own (and use) this one and a different brand with a different mechanism and they're both flimsy. This holder absolutely will not work outdoors.

Q: 10. Will this case fit the Nikon 18-55mm VR II lens or will I need to go bigger?

A: I holds my 18-140 (but very tight and bulges a bit at bottom) so it should hold the smaller lens.