Able to withstand a wide range of temperature extremes, the RF-Video LX-1015/2 Video/Audio Transmitter 1000 to 1500 MHz is a lightweight wireless video/audio transmitter that weighs about 3/4 of a pound and supports NTSC / PAL video, making it suitable for use as a transmitter for flying platforms. It features over 3.7 miles of line of sight transmission of the analog video signals. Frequency selection is digitally controlled in 250 kHz steps from 1000 to 1500 MHz. A digital LCD display confirms your Frequency selection. Please note that this item is only available for sale to government agencies, and is not for commercial use within the United States.

Only for Sale to Government Agencies    Supports Wide Temperature Range    Wireless Video & Audio Transmission    Supports NTSC & PAL    Over 3.7 Mile Line of Sight Transmission    Digitally Controlled Frequency Selection    1000 to 1500 MHz    Digital Display

• Frequency is selectable from 1000 to 1500 MHz in 250 kHz steps
• Push button control, up and down for frequency selection

• The transmitter can work at extreme temperature ranges from -40 to over 170°F

• Video/audio is input via an F connector

• Low power consumption of 1600 mA at 12 Volts DC

• The transmitter accepts from 9 to 16 Volts DC (12 Volt recommended)

Related Questions and Answers

Q: 1. under optimal conditions, what is the range?

A: Under optimal conditions, you can get up to 1,000 ft of coverage with this transmitter and our LA-122 antenna. Different antenna's can have different coverage area's, with LA-122 giving the most. If you are looking for more coverage, I would recommend our 216 MHz system which can give up to 3,000 ft of coverage. Thank you.

Q: 2. audio channels?

A: The audio outputs on this device through RCA. You would just need basic RCA Male to Male cables.

Q: 3. It needs 12VDC 1.3A (15.6W), but is the barrel centre-positive or centre-negative?

A: The Listen Technologies Stationary RF Transmitter (216 MHz), BH # LILT80021601, features a center-positive 12VDC input port.

Q: 4. I have a video switcher with Program out via SDI, I am told there is embedded audio running out with the SDI video signal. Will this unit work for my application? I want my SDI PRGM output from my switcher to feed into a standard LCD TV monitor via HDMI with video and sound. I want to set up client monitors in the Greenroom down the hall .. All my SDI feed does for my consumer HDMI TV is video only...Thanks

A: Hi James, This is Jules from Symbiosis, Decimator's Master Distributor for your territory. The Decimator 2 will all you to pass both video and embedded audio from the SDI input to the HDMI output for monitoring on your LCD TV. Just in case you need it, there is also a pair of analog line level outputs for driving an amplifier or set of active speakers as well. I hope this helps. Jules

Q: 5. one antenna to receive two different signals(frequencies) by two receivers ; is it possible to use in this way?

A: Yes, the RF Venue 2X1SPLIT Passive Splitter/Combiner can be used with one antenna to receive audio signal and then route it to two different receivers. The antenna and receivers that you use will also determine the capabilities of the setup. The 2X1SPLIT functions as a router.

Q: 6. Will the '16:9 to 16:9 anamorphic' analog setting output a SD signal with no pillar or letterboxing added to a 16:9 source?

A: When using the DECIMATOR 2 3G/HD/SD-SDI to HDMI Converter with Built-In NTSC/PAL Downscaler & Analog Audio Outputs, you can configure the Decimator 2 to output analogue SD signals as a 16x9 anamorphic signal as well as options for letterboxed and straight 4:3.

Q: 7. I need to convert PAL signal to NTSC signal so I can send it into my video switcher then out to my projector. I am using this in the US, but my client is sending me a Broadcast in PAL. for the audience to view. can this unit do this?

A: Yes, the Decimator 2 3G/HD/SD-SDI to HDMI Converter with Built-In NTSC/PAL Downscaler will be able to convert SDI in PAL to NTSC in a composite down scaled format.

Q: 8. Is it compatible with gopro hero 4?

A: This unit has RCA Composite Inputs for the video feed. It may be possible to use it with a GoPro Hero4 if you have the composite cables for the camera. They are B&H #GOACMPS.

Q: 9. Can the Decimator 2 simultaneously downconvert the input to composite while passing through the original format to HDMI?I want to input 720p59 over HD-SDI and output both 720p59 over HDMI and downconverted NTSC composite (anamorphic).

A: From what I have read, yes it can, however I will double check and get back to you. However, I am using 1080p/60 so there may be a difference for you. But this thing is fantastic

Q: 10. Will this unit support the downconversion of an HDMI signal from a laptop to composite video? I want to use it to send an HDMI signal from a Mac laptop to a Presidential-type teleprompter system.

A: Sorry, while Decimators are great products, this one is not right for your application. Use this one, (as long as the signal is HD) Atlona HDMI/DVI to Composite and S-Video Down-Converter B&H # ATHD530 .