Finished in black with silver and chrome hardware, this Flight Zone Glide Style Case from Odyssey Innovative Designs is designed to house a Traktor Kontrol S4 MK3 DJ controller and provide full protection from the rigors of on-the-road wear and tear. The case features a Glide Style laptop platform with two cable port holes and a removable V-cut panel for accessing the controller's front input jacks. Set up the glide platform in the standard flat configuration, or utilize the attachable angled support panels to position it with a tilt for improved visibility and ergonomics.

The patent-pending bevel foam interior keeps your controller snug and secure while the heavy-duty ball corners and hardware enhance exterior protection. Store cables, adapters, and accessories in the side compartments and open space beneath/behind the controller. Durable rubber feet prevent the case from sliding and obviate scratches to your tabletop. The recessed handle and latches ensure simple transport between gigs.

Note: For the safety of your equipment, do not transport with gear stored on the glide platform, and be aware that the platform can be removed when slid out to its furthest point.

For Traktor Kontrol S4 MK3 DJ Controller    Glide Style Laptop Platform    Removable Front Access Panel    Side Storage Compartments    Attachable Angled Support Panels    Multiple Cable Port Holes    Bevel Foam Interior    Recessed Handle & Latches    Heavy-Duty Ball Corners & Hardware    Durable Rubber Feet

• Patented Glide Style 24.5 x 11.75" (W x D) laptop platform with two cable port holes
• Glide platform tension latches
• Includes attachable angled glide platform support panels
• Convenient side storage compartments for support panels or accessories
• Configure the gliding platform in the standard setup with a flat top surface, or add the included side support panels to position the platform higher and at an angle
• Removable V-cut front access panel
• Bottom rubber feet
• Heavy-duty ball corners and hardware
• Generous cable management space beneath and behind controller
• Patent-pending bevel foam interior
• Bottom cable port for ideal cable management
• Recessed handle and latches

Related Questions and Answers

Q: 1. can i mount this slider on one allex tripod ?

A: If you used just one typical tripod for the Libec ALX S12 Slider it would not be for long. With your first move to one end, your camera would crash to the floor.That is becasue the ALX S12 at 43.5 /110 cm is too long for one typical tripod. You need two stands of some sort for it or use it on a table top. See the two mounts underneath the slider for attachment to confirm this.If you were using the short ALX S8 Slider (28 ), then one tripod would be fine.

Q: 2. Will this fit into a Kupo Runway Base stand (Wheels)The base has a 11/8 inch reciever ?

A: It should it has a 1 1/8 pin

Q: 3. what type USB cable is used, i.e. type 2.0, type C, etc. ?

A: This joystick uses a USB-A 2.0 cable connection.

Q: 4. Can ther hook up to a remote fash? If so, which remote do you recommend?

A: This is a continuous light kit, therefore it cannot sync with the cameras as done with a flash.

Q: 5. Is this light dangerous to my skin if I shoot often ? Do fluorescent lights emit uv light and dangerous for skin ?

A: The Impact FF-S4 3-Light Daylight Softbox Light Kit should be fine for standard still photography and video usage needs. However, if you will be shooting with the lights positioned closer than approximately 10 inches (30 cm) from your subject without moving for longer than 6 hours a day, then you may wish to purchase replacement lamps such as the ALZO 15W Joyous Light Dimmable Full-Spectrum LED Bulb (5500K, 4-Pack), B&H # AL275504DIFS • MFR # 2007-55-04-DI-FS, for your usage needs.

Q: 6. What is the weight capacity just for the riser? It would be mounted in a Junior baby plate mounted on a deck.

A: Matthews, only lists the support weight for the Matthews Riser Section for C+ Stand (40") when attached to C stand legs. And that is a maximum of 22 lbs.

Q: 7. Is this item the baseboard only or the baseboard along with the mount for the head?

A: The Beseler Baseboard with Hardware for 23CIII-XL Enlarger includes the baseboard and the hardware to attach the enlarger to the baseboard.

Q: 8. Hi does anyone tried this slider with the c500 ? would you recommend it for that camera?

A: I have been nothing but pleased with this rig with my EOS 7D and the C500 - the only trick is that the C500 is Heavy and would need an additional tripod at the end of the travel of the slide or it might tilt. Some use 2 ALX system tripods either end, but I just used mine with the ALX in the center with a static old lighting tripod screwed into one end ( 1/4 20thread holes on both ends ) Most efficient, compact and performance based excellence in my whole kit. Keep the Slider Rails Clean ( !!) and you'll be amazed at the heavy-duty fluid head for Very smooth moves. Practice and enjoy!

Q: 9. The FF-OF4 is 100-240 vac, however the 4 Socket Fluorescent Fixture is only 120 vac. I need light that all run at 220v, why would a kit have a setup that is not both 100-240vac?

A: This 3 Light Fluorescent Kit. The Impact FF-S4 Three Light Daylight Softbox Light Kit B&H # IMFFOF43LSBK (B&H Kit) is dual voltage 100-240 vac.

Q: 10. With the legs and tripod mount removed, it is possible to directly (and permanently) secure this slider to a tabletop?

A: This is possible to fabricate.