The beige Series 8 CO2-8WLp Dual-Element Omnidirectional Lavalier Microphone from Point Source Audio pairs two microphone elements into a single housing to create a sleek form factor and ultra-low-profile lavalier microphone. It can be used to capture audio and offers built-in microphone redundancy for wireless transmitters in live stage, theater, and broadcast applications.

The CO2-8WLp's dual elements are factory matched to a near identical ±0.5 dB difference and both elements are IP57 waterproof rated. The microphone cable splits approximately 9" above the connection to the bodypack to allow for ample room for separation of the transmitters. In addition, the mic is equipped with a 6' cable that terminates with two 3.5mm locking X-Connectors for Sennheiser EW Series transmitters.

For Wireless Bodypack Transmitters    2 x XSE X-Connector Adapters    2 x Microphone Elements in One Housing    Factory Matched in Frequency/Sensitivity    20 Hz to 20 kHz Frequency Response    Water, Sweat, and Makeup Proof    IP57 Waterproof Rated    Includes Slider Clip    Cable Clip and Windscreen    Interchangeable X-Connector

3.5mm locking X-Connectors for Sennheiser EW Series transmitters

Two Mics in one—dual matched waterproof elements for built-in redundancy

136 dB max SPL

IP57 waterproof-rated

Optimal gain before feedback

Related Questions and Answers

Q: 1. does it work with a tascam remote?

A: Irin,No it does not.Full details on the DR-10L here: a href= http://tascam.com/product/dr-10l/overview/ target= _blank http://tascam.com/product/dr-10l/overview//aThank you for your interest in TASCAM products.

Q: 2. Can you use other upgraded lavalier capsules, such as a Tram TR50, with this recorder?

A: The Tascam DR10L features a 1/8 locking connector that is compatible with lavalier mics terminated for Sennheiser wireless systems. There is a Tram TR50 with proper termination. See B&H# TRTR50BSETP .

Q: 3. Should I use a 1/8" TRS or 1/8" TS to XLR for a balanced XLR input?

A: You will want to use an 1/8" (3.5mm) TRS male to XLR male cable to connect the output from the wireless receiver included with the Mackie EleMent Wave LAV Compact Digital Wireless Lavalier Microphone System to a balanced XLR input. The output connector on the wireless receiver is TRS.

Q: 4. I want to use my iphone 8 as a recorder which does not have a headphone jack. I could just use an adapter for that, right? I want to be able to record on my phone and monitor from the headphone jack on the receiver. Can this be set up this way?

A: To connect the receiver of the Mackie EleMent Wave LAV Compact Digital Wireless Lavalier Microphone System for Cameras and Smartphones to the iPhone, implement the included TRS to TRRS output cable alongside the Apple Lightning to 3.5mm Headphone Jack Adapter (BH #APLAADAP): https://bhpho.to/3KpYrG8. The receiver in the EleMent Wave LAV system includes a dedicated headphone jack for monitoring while simultaneously outputting signal to your phone or other device.

Q: 5. is there any link here to mic the bride using this? Thank u in advance

A: I'm sure you could do it, but I'd suggest doing the groom instead. It's hard to predict what kind of dress they will have. It picks up both quite nicely and with the dual record, you can even set your gain a little higher for her voice.

Q: 6. The manual says no less than 3 meters between transmitter and receiver. I want to use a smaller distances sometimes. Will it work? What will I get at 2 meters? I am not concerned about the maximum distance of 70 meters. I am concerned about going below the minimum distance of 3 meters. Please answer with regard to effect of using at 2 meters. Thanks.

A: The Mackie EleMent Wave LAV will work at less than 3 meters between the transmitter and the receiver.

Q: 7. Which version is this, V1 or V2, or is it just a firmware/software update?

A: There's only one version of this unit, they have a firmware update that can be done once you purchase the unit.

Q: 8. Can I connect my Rode Videomic shotgun mic to the Tascam DR-10L mic input? It also has a 3.5mm, 1//8 connector.

A: Most probably yes. I use the DR-10L with sE Electronics ProMic Laser (search B&H for specs) and they work well together.

Q: 9. Is the microphone available to be purchased anywhere seperately

A: Eric H,You can order it from our Parts Department (parts@teac.com).Thank you for your interest in TASCAM products.

Q: 10. How do I monitor the audio during recording?

A: Hi, theres a headphone out. But with my unit it sounds kind of crappy. I read online that the headphone out is soft. So I just trust it is working fine. And of course it is fine on the computer.