The white T91B57 Pole Mount from Axis Communications is designed to be used with select Axis T91 wall mounts and T98A enclosure cabinets on poles ranging from 4-16" in diameter. This mount is also compatible with the Axis A9188-VE relay module and TX30 steel straps. It has a 66 lb maximum capacity.

This mount offers cable routing from its back and bottom and comes with two stainless steel straps along with a cable gasket for protection against insects. It is housed in an IK10-rated aluminum casing that is suitable for use in areas at risk of vandalism.

Designed for 4-16" Pole Diameters    For Select Axis T91 Wall Mounts    For Select Axis T98A Enclosure Cabinets    66 lb Maximum Load    Cable Routing    Includes Stainless Steel Straps    Includes Insect-Proof Cable Gasket    IK10-Rated Vandal Resistance

Designed to be used on poles ranging in diameter from 4-16"

Indoor and outdoor use

66 lb maximum load

Cable routing on the back and bottom (Axis T91G61 or T98A required for bottom cable routing, available separately)

PVC free

Includes insect-proof cable gasket and two stainless steel straps

Related Questions and Answers

Q: 1. Is anyone using this to hang 53" seamless? I'm assuming it would require using only one of the poles? If that is the case can each part of the pole be used for two separate 53" seamless paper rolls?

A: This crosspole can be used to replaced the cardboard core on a 53" seamless, so you can use a set of Impact Varidrives to bring the roll up or down as needed. If you were using two 53" rolls, it may be difficult to connect the two sections since one section fits completely flush to the roll.

Q: 2. Can you position your phone vertically with this mount, or only horizontally?

A: Horizontal only.

Q: 3. How secure is the pole? Will it spin easily?

A: The gear doesnt come with a pole. I bought a hreen screen backdrop that has two tripods that have a pole that is connected on the top. I put the gear on that pole and yes it can spin easy but when you tighten the screws it wont spin. Its working out very good for me because the green screen kit is adjustable and it was inexpensive.

Q: 4. I want to mount the Sennheiser Ambeo VR Mic to this monopole using a magic arm (below a KanDao Obsidian R camera). Can you recommend a magic arm that's compatible with both?

A: You could consider clamping that mic to this pole with the CAMVATE Crab Clamp with 5/8"-27 Ball Head Mount for Microphone, BH #CAC1465. https://bhpho.to/2OuPxzb

Q: 5. Doesn't this press on side buttons? The spacing of the clamping arms looks like they'll hit camera and on/off buttons on iPhones

A: The JOBY GripTight ONE Mount for Smartphones (BH #JOJB01490) allows for a phone to be adjusted so no buttons are pressed when clamped.

Q: 6. Is it possible to connect two of these units together to get a monopod length of 20' ? I'm doing photogrammetry of tall statues.

A: The Nodal Ninja Collapsible Carbon Fiber Travel Pole (9.6') can work, but only to add one more section, not two. It is not sold separately, so you would need to purchase two of the full kit.

Q: 7. How long will the background drop be

A: This cross pole can accommodate a 9 foot wide roll of seamless paper.

Q: 8. What is the pole bottom thread, 1/4 or 3/8?

A: Bottom thread is a female 3/8 -16

Q: 9. Is the large VR Pole stable and safe to use (up to its weight capacity) without the Manfrotto Carbon Fiber VR Tripod?

A: The Manfrotto Carbon Fiber Boom Pole for VR Camera (Large) will work great with any camera within the 4.4lb weight limit, and will provide a safe and stable support. The pole will need to be held by the user, but you have access for further support accessory attachment via the 1/4"-20 thread at the bottom of the pole.

Q: 10. Does it accept a cold shoe mount?

A: The GripTight ONE has only a 1/4"-20 tripod jack, but you can use a cold shoe adapter like this: https://bhpho.to/2GWl5Yi