Replace the air filters on your Afinia H+1 3D printer with the Afinia HEPA and Activated Carbon Dual Air Filter Set. These large filters reduce ultra-fine particle (UFP) emissions and eliminate odors from 3D print jobs. The H+1 3D printer has a powered, recirculating air filter system, which has been proven to reduce emissions up to 91%, compared to other 3D printers. The air filters make the H+1 3D printer safe for use in the classroom and office.

Afinia recommends that you replace this filter set every 6 months or after 300 hours of use, whichever comes first.

For Afinia H+1 3D Printer    Eliminate UFP Emissions and Odors    Reduces Emissions up to 91%

Related Questions and Answers

Q: 1. Do these come with the required screws to attach to a pair of Impact Superclamps?

A: I purchased the heavy duty drywall anchors and washers from big box home improvement store.

Q: 2. What do you use to prevent the paper roll from sagging in the middle? I plan to use on savage 107

A: I use a piece of 3/4 inch EMT. Readily available at Lowes or HomeDepot.

Q: 3. Does anyone know what is the diameter of the slots? In other words if I want to put a crossbar instead, what should be it diameter to fit on the slots

A: 11/16" or 17.5mm

Q: 4. Will these work on a Savage Backdrop/background support stand?

A: They should work but be careful. You can easily over tighten these and crush hollow tube stands. These work best with heavier material like you get on steel stands.

Q: 5. What is the distance from the bottom of the top hook plate to the top of the bottom hook plate. The measurement in between.

A: The distance between the bottom of the top hook plate to the top of the bottom hook plate on the Impact Background Dual Hooks (Set of 2) measures approximately 3 3/4 inches

Q: 6. Hi, Could someone please tell me how far apart these brackets need to be mounted for the Varidrive system with the varidrive metal core background poles? Many thanks!

A: Depends on the size of the role you are using. You need the length of the role plus about 2-4 inches on each end. This gives you room to adjust on both sides.

Q: 7. Is there a better ND option than gelatin sheets?

A: There are no ND filters desing to fit Canon RF 5.2mm f/2.8 L Dual Fisheye 3D VR Lens rear mount. However if you own Canon R6 II/R6/R5/R3 you could connect the following ND filter infront of the camera sensor. Kase 3-in-1 ND Set for Canon EOS R5/R6 Camera Bodies (ND8/ND64/ND1000) BH #KA1128060001 • MFR #1128060001 https://bhpho.to/2JcQee8

Q: 8. Does the focus use hard stops? Hoping to use DJI Lidar to make an autofocus solution.

A: The Canon RF 5.2mm f/2.8 L Dual Fisheye 3D VR Lens does not have hard stop focus.

Q: 9. Can these hooks be mounted on a wall instead of a pole and does anyone know the measurements of the hooks (total length top to bottom, especially)?

A: The hooks by themselves can be mounted to a wall however, the knobs that turn (that come with the hooks, you will not be able to attach them to the hooks. Reason way, you will not have enough turning clearance from the wall to actually turn the knobs.

Q: 10. What crossbar is needed to hold a seamless paper roll up?

A: These hooks are meant to be used with the varidrive pulley system. At the moment there is no crossbar that would be used. You can find the varidrive pulley system here: https://www.bhphotovideo.com/c/product/822879-REG/Impact_vpd_dsg_Background_Paper_Drive_Set.html