The white HDMI over HDBaseT Wall Plate Transmitter & Receiver Basic Kit from AVPro Edge features a single-gang wall plate transmitter and a compact receiver that enable you to transmit HDMI and VGA signals over a single Cat 6a/7 cable. This point-to-point HDMI extension solution offers 4K60 4:2:0, 4K30 4:4:4, DCI 2K, and 1080p video support and up to 2560 x2048 (QXSGA) VESA support.

This HDBaseT set can send HDMI 4K60 and HDR video up to 131' and 1080p up to 230' via a Cat 6a/7 cable. Video is input via the transmitter's HDMI 2.0 port and output to the receiver via a rear RJ45 receptacle. Set features include support for HDCP 2.2 and earlier, a rugged chassis, plug-and-play auto input-sensing, support for multiple audio formats, and compatibility with HDBaseT displays, projectors, and A/V receivers.

Single-Gang Wall Plate Transmitter    HDMI Type-A 2.0 In, RJ45 Out to Receiver    HDMI 4K60 & HDR up to 131' on Cat 6a/7    HDMI 1080p up to 230' on Cat 6a/7    PoE Wall Plate Transmitter, PSU Option    Up to 10 Gb/s / 4:4:4, 4:2:2, 4:2:0    Compliant with HDCP 2.2 & Earlier    Plug-and-Play Auto Input-Sensing    Supports Multiple Audio Formats

Point-to-point HDMI extension solution for conference and huddle rooms

HDMI 2.0 input

Supports 4K 30 4:4:4 and 4K60 4:2:0 HDMI resolutions

Supports DCI 2K, 1080P, and 1920 x 1080 x 60 VGA resolutions

Extends HDMI 4K60 and HDR video up to 131' and 1080p up to 230' via a Cat 6a/7 cable

Single-gang, low heat, straight-in, rear RJ45 receptacle design

Supports HDCP 2.2 and earlier versions

Related Questions and Answers

Q: 1. If the transmitter is sending with hdmi output, will the receiver be able to output the signal through Sdi?

A: Yes, the Vaxis Atom 500 can receive an HDMI signal and send out the same signal through SDI.

Q: 2. Can there be multiple transmitters to one receiver?

A: Unfortunately no that is not possible.

Q: 3. Does this receive and sends 59.94i

A: Yes. In the following formats SDI/BNC: 1080p at 25, 29.97, 30, 50, 59.94, 60 fps 1080i at 50, 59.94 fps 720p at 60 fps HDMI: 1080p at 24, 25, 30, 50, 60 fps 1080i at 50, 60 fps 720p at 60 fps

Q: 4. if i use SDI for the transmitter, can i also use HDMI for the receiver?

A: Yes, you can use either plug on either device, it doesn't affect the signal.

Q: 5. On the receiver, can you output from both the SDI and HDMI at the same time?

A: Yes, The Vaxis ATOM 500 RX can output from both the SDI and the HDMI port simultaneously.

Q: 6. Hello, can I use multiple receivers with one transmitter?

A: The Vaxis ATOM 500 will connect to one receiver and a mobile device.

Q: 7. The transmitters keep getting very hot and the picture freezes..how can we overcome this?

A: Wireless video transmitters tend to get hot without much of a workaround. It might be best to move onto a system with built in heat syncs similar to teradek.

Q: 8. how much is latency?

A: This is rated at 80 ms for latency. It is very low in latency.

Q: 9. if tx is using hdmi, could rx transmit via sdi?

A: The RX could output via SDI or HDMI.

Q: 10. I have a sony Battery NP-F970. Which Sony mounting plate would that fit?

A: If you have a Teradek system with a 2 Pin Lemo connection for power you will need the Teradek L-Bracket Battery Plate for Sony L-Series or Canon LP-E6 Battery instead, BH #TE110759. https://bhpho.to/2ZcejnF