Use the oval base 1/4"-20 Screw Wall Mount from CAMVATE to mount a microphone, camera, or accessory onto a table, wall, ceiling, or other flat surfaces. This aluminum alloy mount incorporates a 1/4"-20 thread and includes a removable 1/4"-20 screw. It comes with an Allen wrench and mounting screws.

Mounts onto Table, Wall, or Ceiling    1/4"-20 Thread + Removable 1/4"-20 Screw    Oval-Shaped Base    Secures Mic, Camera, or Accessory    Aluminum Construction    Screws & Allen Wrench Included

Related Questions and Answers

Q: 1. What is the angle in degrees of tilt?

A: The 3 Legged Thing LVL-BASE Levelling Base Screw-On Attachment for Tripods has 10˚ tilt in each direction from level.

Q: 2. Can I apply a kirk quick release clamp to this ballhead?

A: You are not able to interchange them however you can screw the Kirk QR adapter into the 1/4 -20 thread of the ball head.

Q: 3. I'm not good at English. I am very sorryIs this not the new MONOBALL Z1 +?

A: No, it is not. However, there are several versions of the monoball z1+. Here is a link to all the options: https://bhpho.to/2raIdro

Q: 4. does it come with lever clamp ?

A: Yes, a lever clamp is included with the LVL-BASE.

Q: 5. Could anyone kindly let me know if the 1/4" 20-thread stud could be replaced by a 3/8" 16-thread stud? I know I can use an adapter sleeve, but my question is whether the stud itself could be replaced. TIA, Roy

A: No, when using the "Arca-Swiss Monoball Z1 sp (Single Pan) Ballhead with 1/4"-20 Screw", the 1/4" 20 thread stud cannot be replaced by a 3/8" 16 thread. But, the Arca-Swiss Monoball Z1 sp (Single Pan) Ballhead is available with a 3/8" 16 thread: https://bhpho.to/2ncKVhr

Q: 6. Will this fit 701hdv fluid head?

A: yes it does

Q: 7. Does the knob have friction control?

A: Yes, the following unit offers PMF tension control.

Q: 8. Hi.I own an old Davis & Sanford Carbonlite Transporter with a Z10 head.I am wondering if the Z1 would fit on my tripod (instead of my current Z10) and if so which screw I should choose (1/4 -20 or 3/8 )?Actually, I wish I could get the Z1 head with the Wimberley C-12 Quick Release Clamp in order to add a P-30 QR Plate, but all of that without having to buy a new tripod.Thanks a lot for your forthcoming answer.

A: Your helpful answers were exactly what I needed.Thanks a lot to you all.

Q: 9. Hi! I just bought this AS Monoball Z1 sp w flat disc, assuming I could remove the disc and install an RRS QR system, however read conflicting article that it will not be user replaceable. I will send it back if thats the case. Can I remove the flat disc or not? I don't want to screw the RRS QR plate on top of the disc. Thanks

A: I bought the Arca Monoball Z1 sp with the flat disc in 2014, and proceeded to do exactly as you intendremove the flat disk and install the RRS QR clamp. My procedure was to firmly clamp a 3/8 bolt into my vise and then mount the Z1 to that bolt. Then I positioned the flat plate into the Z1 vertical slot (the 90 degrees slot) and firmly tightened all the Z1 controls. Then fit an appropriate socket to the hex-head attaching screw and apply CCW force (the screw is a common right-hand-thread). The relief around the hex-head attaching screw is tight, so it may be necessary to fit a thin-wall socket. In any case, be certain the socket gets fully inserted on the hex to avoid rounding off the hex. I used a long handled ratchet on my 3/8-drive socket to allow me to apply the necessary torque (around 20 to 30 foot-pounds).In late 2013 the photo press mentioned that Arca had replaced their thread sealant with a more permanent epoxy type, which was impossible to remove. I purchased my Z1 in mid 2014, and the flat plate was easily removed with moderate torque.However, if your later-issue Z1 proves recalcitrant, try applying pinpoint heat to the hex-head attaching screw immediately prior to applying removal torque a few seconds with a propane torch should add the necessary heat. Or simply send the Z1 to their US repair facility (Precision Camera) and let them do it for a few dollars. Turn-around time is usually very fast, and it will be money well spent.Ive used a selection of ball heads, and I feel the Z1 to be one of the best. Coupled with an RRS clamp, this is an excellent platform.

Q: 10. Can this be mounted on the head - Really Right Stuff Lever-Release Style Quick-Release Clamp, 60mm B&H # REB2LRII MFR # B2-LR II ?

A: Yes, you can absolutely do that.